Results 1 to 9 of 9

Thread: arbitrary connection issues

  1. #1
    Join Date
    06.01.2017
    Posts
    19

    Default arbitrary connection issues

    Hello there,

    I have sometimes some connection losses on my P4 ... The wifi access point is an Apple Time Capsule that works fine with all other devices.
    Connection to the P4 works perfectly and continuously for, say, 3-4 weeks, and then suddenly connection is lost for a few days .... Last time was yesterday and the issue seems to have been solved on its own (works again today)

    Any clue about this issue ?

    PS : I have last versions of firmware for both the P4 and the Wifi : respectively 7,08 and 6512

    Thanks

  2. #2
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,729

    Default

    we recommend to use static IP address
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #3
    Join Date
    06.01.2017
    Posts
    19

    Default

    Hello Matthias,

    Thanks for the answer but, yes I have done that already .... =Defined DHCP reservation on my router (192.168.0.200) + "Use the Following setting" in the communication Tab of GCC 1.1.0.3 ...

  4. #4
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,729

    Default

    you have old versions of GCC (is now 1.1.1.1), firmware (is now 7.11) and WiFi firmware

    I think you should update everything and go from there
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #5
    Join Date
    06.01.2017
    Posts
    19

    Default

    ????
    the GCC 1,1,1,1 is said to be a beta version, this is why I did not install it ...

    And about the 7,11 : cannot find it on the download page ... Do you mean the wifi-Modul ESP update ?

  6. #6
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,729

    Default

    the version is safe, use it

    firmware is, as always, included in GCC

    Wifi Modul update is separate
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  7. #7
    Join Date
    06.01.2017
    Posts
    19

    Default

    okay for the 1,1,1,1 will do it.

    An finally, should i still install the Wifi modul ?

  8. #8
    Join Date
    06.01.2017
    Posts
    19

    Default

    during firmware update, I get the message "reset the microcontroler on user board" ..... He seems to wait ... What does it mean ?

  9. #9
    Join Date
    06.01.2017
    Posts
    19

    Default

    I have tried unplugging the P4 and replugging .... And tried again the firmware update. The same window as above appears but disappears immediately, but the firmware update lasted very long (more than 30 minutes) .... Unplugged again and at 3rd time if finally worked ....

    Any clue ?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •