Page 1 of 6 123 ... LastLast
Results 1 to 10 of 54

Thread: profilux 3 ex lan problem

  1. #1
    Join Date
    23.02.2009
    Posts
    46

    Default profilux 3 ex lan problem

    i cant connect with my profilux using lan.
    it wont get a ip, when i try to config it with hand i cant ping it.
    profilux-lan.jpg
    should there be serial or lan?

  2. #2
    Join Date
    25.12.2011
    Posts
    30

    Default

    Post some more pictures from your settings.

  3. #3
    Join Date
    23.02.2009
    Posts
    46

    Default

    will do tomorrow after work, been at it now for 2 nights
    this little pic is from the settings before we talked on the phone.
    Attached Images Attached Images
    Last edited by greenbee; 11.04.2012 at 20:26.

  4. #4
    Join Date
    19.02.2009
    Posts
    2,969

    Default

    The built in LAN interface isn't shown as a module.

    Are the LAN LEDs glowing/blinking on the LAN port?
    Did you connect the ProfiLux to a router?

    Please more details on your network and which settings you've made!

  5. #5
    Join Date
    23.02.2009
    Posts
    46

    Default

    hi, the green led is glowing and the amber one is blinking.
    i did set the ip manualy in profilux because auto did not work.
    profilux-lansetings.jpg
    its connected on a linksys wrt 320n router
    the ip from the router is 192.168.1.1 its range is from 1.100 to 1.199
    i also tryed to manualy put mac adres i found on the lan settings in plc into the router dhcp table with 192.168.1.138 as ip.
    i just tryed to conect with laptop and crosscable direct to profilux with laptop ip set as 192.168.1.138, same as profilux and then the ping went ok.
    Last edited by greenbee; 12.04.2012 at 17:51.

  6. #6
    Join Date
    23.02.2009
    Posts
    46

    Default

    after the crosscable check with the laptop i connected all the cables again the same way as it was and its working.
    wierd but true.
    only wonder if there are any templates avalible for the user webpage?
    thx for your help.

  7. #7
    Join Date
    23.02.2009
    Posts
    46

    Default

    and again it failed,
    its not getting a ip when i set it to auto and when i use a fixed ip its not pingable so whats going on?
    it should get a ip

  8. #8
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,729

    Default

    Quote Originally Posted by greenbee View Post
    and again it failed,
    its not getting a ip when i set it to auto and when i use a fixed ip its not pingable so whats going on?
    it should get a ip
    what did you set to "auto" - the search mode of ProfiLuxControl or the internal ProfiLux IP settings?

    is there a DHCP-server?
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  9. #9
    Join Date
    23.02.2009
    Posts
    46

    Default

    hi, yea the internal ProfiLux IP settings, and yea there is a dhcp server.
    it did work for a while and now its not possible to ping, whatever ip is set.
    my router is 192.168.1.1 and it gives ip addys from 1.100 to 1.149
    i tryed alot of ip`s
    subnet mask is set to 255.255.255.0
    default gateway is set to 192.168.1.1
    dns i tryed 192.168.1.1 or 192.168.0.0 or the dns i found in my router 62.45.45.45

  10. #10
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,729

    Default

    ok, we must investigate this further

    1.) if you connect directly over crossover cable (BTW - a normal cable is also OK for direct conenction, then ProfiLux swaps the signals) you have a connection?
    2.) if you go through a rouuter you can't access the ProfiLux
    3.) a powercycle from ProfiLux doesn't help?
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •