Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 38

Thread: Mitras FW

  1. #11
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    I already have done the manual installation of driver as posted on prev entry.

  2. #12
    Join Date
    13.11.2013
    Posts
    1,001

    Default

    Ok, than can you post me a screenshot of your device manager with opened COM & LPT?
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #13
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Driver WAS installed manually before opening this thread

  4. #14
    Join Date
    17.11.2012
    Location
    Louisiana
    Posts
    192

    Default

    If your plugging into a USB 3.0 try plugging into USB 2.0 instead, that's the only way I can get it to work.
    Perry
    A screen shot is worth a thousand words...

    Profilux 3.1N eX, 3 PAB 6D, Slave Doser, PLM-ADIN, Vortech Controller, PLM-PWC, Leak detector, 2 LX 6100HV Mitras
    Controlling a 150 DSA Peninsula mixed reef.

  5. #15
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    And how do I determine which USB is 2 or 3?

  6. #16
    Join Date
    17.11.2012
    Location
    Louisiana
    Posts
    192

    Default

    See if you have a 3.0 controller in Device Manager under the USB controllers. If not, then moot point. If you do you can try different ports. I know USB is supposed to support legacy, but on my computer I have four ports, one is 2.0 and it's the only USB port that allows me to connect to Mitras or Profilux to update firmware.
    Perry
    A screen shot is worth a thousand words...

    Profilux 3.1N eX, 3 PAB 6D, Slave Doser, PLM-ADIN, Vortech Controller, PLM-PWC, Leak detector, 2 LX 6100HV Mitras
    Controlling a 150 DSA Peninsula mixed reef.

  7. #17
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Thank you very much. Will try that tonight and will provide screenshots as needed.
    Thank you very much

  8. #18
    Join Date
    06.02.2012
    Posts
    2,020

    Default

    And how do I determine which USB is 2 or 3?
    USB 3.0 ports usually have a blue plastic connector instead of the black ones of USB 1.1/2.0

    Of course, it´s not a requirement for USB 3.0 but a used way to differ between the port standards

  9. #19
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Quote Originally Posted by Halfmoon View Post
    See if you have a 3.0 controller in Device Manager under the USB controllers. If not, then moot point. If you do you can try different ports. I know USB is supposed to support legacy, but on my computer I have four ports, one is 2.0 and it's the only USB port that allows me to connect to Mitras or Profilux to update firmware.


    Under USB controllers this is what I have. I believe they are 2.0

  10. #20
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Quote Originally Posted by Artur View Post
    Ok, than can you post me a screenshot of your device manager with opened COM & LPT?

    Here you go


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •