power bar problem after installing touch and wireless card ( for mitras) sockets 5 6 7 on the power bar current reading fluctuactes between proper reading ( 0.3) to 15.45 .
power bar problem after installing touch and wireless card ( for mitras) sockets 5 6 7 on the power bar current reading fluctuactes between proper reading ( 0.3) to 15.45 .
profilux 3x wireless enabled 3 ecotech pumps and wireless adapter
3 Simuspots 2 levl sensors ( min /max)
4 channel dossing pump 2 PAB 6 outlets
Temp PH and redox sensors 2 mitras 6100HV
touch Condutivity sensor wireles card
do you have more than 1 powerbar?
then check start number assignments
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
yes I have 2 power bars not sure what you mean (check start numbers)
profilux 3x wireless enabled 3 ecotech pumps and wireless adapter
3 Simuspots 2 levl sensors ( min /max)
4 channel dossing pump 2 PAB 6 outlets
Temp PH and redox sensors 2 mitras 6100HV
touch Condutivity sensor wireles card
Please check which start numbers you have assigned to each Powerbar.
E.g. start no. of Powerbar 1 = 1, i.e. sockets are numbered from 1 to 6
start no. of Powerbar 2 = 7, i.e. sockets are numbered from 7 to 12
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
my dosser takes numbers 1-4 powerbar 1 starts 5 - 10 power bar 2 starts 11-16
profilux 3x wireless enabled 3 ecotech pumps and wireless adapter
3 Simuspots 2 levl sensors ( min /max)
4 channel dossing pump 2 PAB 6 outlets
Temp PH and redox sensors 2 mitras 6100HV
touch Condutivity sensor wireles card
and the powerbars (resp. the sockets in them) are still reacting on the right socket channels?
it is possible that they have overlapping number-ranges which results in strage current-readings
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
if I discconnect the touch all is ok. if I plug it into the PAB connection on the Power bar it stays on the 15. 45 current on the 3 sockets if I connect to pab on back of profilux then it fluctuates from 0.3 to 15. 65
profilux 3x wireless enabled 3 ecotech pumps and wireless adapter
3 Simuspots 2 levl sensors ( min /max)
4 channel dossing pump 2 PAB 6 outlets
Temp PH and redox sensors 2 mitras 6100HV
touch Condutivity sensor wireles card
I would give reassign all the PAB devices a try.
profilux 3x wireless enabled 3 ecotech pumps and wireless adapter
3 Simuspots 2 levl sensors ( min /max)
4 channel dossing pump 2 PAB 6 outlets
Temp PH and redox sensors 2 mitras 6100HV
touch Condutivity sensor wireles card
the P3 firmware doesn't matter
are all PAB-devices up-to-date?
please generate a "system-report" (under PLC system) and post it here
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
Bookmarks