Page 1 of 2 12 LastLast
Results 1 to 10 of 18

Thread: Cannot connect via app after update

  1. #1
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default Cannot connect via app after update

    Can't connect using app after upgrading version 6.0. When I open app it tells me wrong password.
    No changes were made to password settings.
    I am able to connect to P3 wired via RS 232 and via TCP/IP using newest version of PLC
    Any suggestions?

  2. #2
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    And now for some reason when I go into PLC to verify password I try to change it and it's not letting me change it...reverts me back to the same password BUT I CANT EVEN LOG ON USING Admin and password!

  3. #3
    Join Date
    30.10.2010
    Location
    Hong Kong, Hong Kong
    Posts
    159

    Default

    Same situation but what I did is go into PLC retype the password and save it, delete and recreate the connection in app, finally OK again.

  4. #4
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Tried that.
    Only issue is that I CANT change and save the password in PLC.
    When I try to do that it boots me out and gives me error 3

  5. #5
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    Quote Originally Posted by doggydoc10 View Post
    And now for some reason when I go into PLC to verify password I try to change it and it's not letting me change it...reverts me back to the same password BUT I CANT EVEN LOG ON USING Admin and password!
    how do you know this?

    all you see are some asterisk

    delete both passwords (empty textbox) for both for a test

    can you access now?

    let us go from there
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  6. #6
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    I cannot delete password.
    When I delete all asterisks and hit save, then I hit load again and when I go back to system I get this again...


    PLC 6.0 and Profilux 3 v 600

  7. #7
    Join Date
    30.10.2010
    Location
    Hong Kong, Hong Kong
    Posts
    159

    Default

    Even if your password is three characters, as default it will show 8 asterisk. So just clear the password and input new one, hit save and load again is OK.

  8. #8
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Done that plenty of times
    Still not able to connect to web interface

  9. #9
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Ended up erasing PLC, resetting and reinstalling and I was able to connect.
    Not sure why it hap but all is back to normal.
    Thank you.

  10. #10
    Join Date
    08.02.2013
    Location
    Victoria BC
    Posts
    164

    Default

    I have also lost webinterface and app connection. I have done as you have even updated plc to 6001 but still no luck. would realy like to get web interface back as the graphs were great. PS last week I finally got it all working on 5.17 but updated profilic to ver.600 and now no connection
    profilux 3x wireless enabled 3 ecotech pumps and wireless adapter
    3 Simuspots 2 levl sensors ( min /max)
    4 channel dossing pump 2 PAB 6 outlets
    Temp PH and redox sensors 2 mitras 6100HV
    touch Condutivity sensor wireles card

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •