PWC Issues

[-Aaron-]

1.)
Working in the light composer:
The settings are transmitted to the light channels of the ProfiLux. Then click Save, the settings are held in the ProfiLux now.
ProfiLux broadcasts these settings to the lamp, the lamp keeps these settings temporarily and works with them.
Remember: The settings are kept (and edited) in the ProfiLux- the Mitras is a "stupid" slave device now.

3.)
Check the channel assignments in the light composer. If you use a template or a lc project from GHL Control Center they should be correct.

PS:When I check your light composer screenshot I see that you have always the same light color, at every time. Therefore always the same LEDs are active. I think the problem is in the light composer project.

The problem is the the channels aren't working properly, I've just tried again and the corresponding channels are all empty apart from the blue channels, which must be why I only get blues on the light being transmitted.

[Matthias]

Not sure if this is relevant, there is 2 LED's on the PCW card, I only have the red flashing. EDIT: I have the green one on now as well.

If you wanna try my project Matthias to see what it does for you guys it's here.

only the red LED should flash - this indicates that PLM-PWC is sending

if the green LED flashes the PLM-PWC is receiving - which should not happen (at least at the moment)!
this means another master (Mitras?) is sending -> all Mitras must be slave devices

[-Aaron-]

I've set the single Mitras I have back to standalone as I need light on my tank, could this light the green LED?

[Matthias]

The problem is the the channels aren't working properly, I've just tried again and the corresponding channels are all empty apart from the blue channels, which must be why I only get blues on the light being transmitted.

I think the project is not correct, it seems in the screenshot that only the blue channels are set correctly - as written before: at every time I can see the same color temperature - there is something wrong

-> load a template and modify it, transmit and save it to ProfiLux, save it as user file for later use

[Matthias]

Same for me to.

1. I cannot find where to load light project except when entering light composer for the first time. There is also not any way of saving a light project either.

2. When loading a user project or creating a new one and then "transmit to channels" PLC6 seems to transmit them but the individual illumination channels are all subsequently set to zero.

3. Everything seems to work Ok if loading one of the templates and then transmitting to channels. So it seems there is an issue only when loading a user developed project.

4. The test illumination run seems to work OK (even without transmitting first.


So it seems there is an issue with user projects.

Thorne

1. There is a menu "light composer" in the menu bar - there is save and load

2 + 3 - maybe there is something wrong with the user project -> please start with a template and modify it

Edit: I just loaded a project from GCC, this has been transfered without problems. It seems to work.

[Matthias]

I've set the single Mitras I have back to standalone as I need light on my tank, could this light the green LED?

no

[-Aaron-]

I think the project is not correct, it seems in the screenshot that only the blue channels are set correctly - as written before: at every time I can see the same color temperature - there is something wrong

-> load a template and modify it, transmit and save it to ProfiLux, save it as user file for later use

I'll have to give this a go then, it's going to be fiddly though getting it exactly as before though.

[Matthias]

I'll have to give this a go then, it's going to be fiddly though getting it exactly as before though.

So what you say is: You saved a project with GCC and then you loaded this project in PLC?

What version of GCC?

If so - Please send me this project by email (I guess you have my personal email address), I'll try to analyze what's going on.
But not before Friday, I am out of office for 2 days.

[-Aaron-]

Basically yes, that's what's happening. I modified it in the latest version of CC and imported it into PLC6. I've just tried editing a template and I'm faced with the same issue, it goes to blues and none of the other channels show. I'll email over my file to you now.

[Matthias]

Ok, your email has been answered

bottom-line:
ProfiLux can only work with up to 12 dimming points per channel pr day (Mitras has 24)
if the project has more dimming points ProfiLux is not able to store it

-> please reduce your projects until it has not more than 12 points, then it can be processed by ProfiLux

I will think about another solution for this issue when I am back