Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: PAR Readings from my tank

  1. #1
    Join Date
    03.06.2012
    Posts
    38

    Default PAR Readings from my tank

    Readings taken with an Apogee PAR meter, all pumps turned off in my tank. Tank had a water change yesterday. To keep the readings consistent I placed the meter's sensor in the tank and took a reading in High Efficiency mode on the Mitras then without moving the sensor changes the lights to High Output mode and took the reading. This was repeated at each level so the results are comparable with my situation.

    Tank Specs; 140x75x55 deep (water level approx 57)

    PAR readings in High Efficiency mode
    240 (sandbed)
    312
    368
    576 (water level)

    PAR readings in High Output mode
    340 (sandbed)
    450
    560
    810 (water level)


  2. #2
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    That's sick. Exactly what was expected from GHL.
    Thanks for that info.

  3. #3
    Join Date
    19.02.2009
    Location
    MANOTICK
    Posts
    866

    Default

    here is some more Rodneyri posted



    In my (uneducated) oppinion this gives a useable PAR spread of about 36"x30x 30" on high output, but please dont go by me see what you think yourself?
    Last edited by aqua_digital; 07.10.2012 at 13:38.


    GHL ProfiLux Canada/USA Distribution and support

  4. #4
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    What settings are you using? Meaning how much "power" are you putting the lights thru?

  5. #5
    Join Date
    19.02.2009
    Location
    MANOTICK
    Posts
    866

    Default

    Here is the power taken

    Quote Originally Posted by rodneyri View Post
    To keep the readings consistent I placed the meter's sensor in the tank and took a reading in High Efficiency mode on the Mitras then without moving the sensor changes the lights to High Output mode and took the reading. This was repeated at each level so the results are comparable with my situation.


    GHL ProfiLux Canada/USA Distribution and support

  6. #6
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,713

    Default

    Hello Rodneyri ,

    would you like to publish your light composer project file?
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  7. #7
    Join Date
    03.06.2012
    Posts
    38

    Default

    happy to email it to whomever is interested, I am in the stage of ramping the lights up so the program isnt full brightness yet and will no doubt be modifed next week as im going to be measuring the light spectrum to fine tune the output a little

  8. #8
    Join Date
    21.06.2011
    Location
    South Florida
    Posts
    827

    Default

    Please email it to me if possible. I can't wait to get my hands on Mitras. But I also don't want to burn my SPS.
    Longodvm@aol.com
    Thanks.

  9. #9
    Join Date
    03.06.2012
    Posts
    38

    Default

    emails sent with light project

  10. #10
    Join Date
    10.03.2013
    Posts
    1

    Default

    Hi rodneyri, could you share and send me your composer light file also? I am new to the Mitras, and was frustrating in tuning this great piece...
    my email: xy
    Cheers

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •