Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 27

Thread: Defective null plug?

  1. #11
    Join Date
    13.12.2009
    Location
    Alberta, Canada
    Posts
    72

    Default

    Yes. There's only three ports on the box, and they're pretty clearly labeled.

  2. #12
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    what firmware version has the P3?
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #13
    Join Date
    13.12.2009
    Location
    Alberta, Canada
    Posts
    72

    Default

    5.06

  4. #14
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    ok, we check this, but we need some time

    can you describe me your hardware configuration in detail, please?

    I want to built an exact copy of it here
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #15
    Join Date
    13.12.2009
    Location
    Alberta, Canada
    Posts
    72

    Default

    PIII firmware 5.06
    Expansion box firmware 1.03
    2 digital 6 plug powerbars firmware both 1.04

    RJ45 wire path:
    PIII > Expansion box > Power bar 1 > Power bar 2

    PIII sensors:
    Temperature
    PH1 probe
    RS232 plug hooked up
    ethernet cable hooked up

    Expansion box sensors:
    Conductivity
    Redox


    on power bar #1:
    1 - 300w heater (set to heater 1 function 27c)
    1 - 300w heater (set to heater 1 function 27c)
    1 - Seaswirl oscillating water direction device (set to always on)

    on power bar #2:
    1 - Reeflo Dart supergold water pump (set on illumination 1 function)
    1 - Reeflo Dart supergold water pump (set on illumination 2 function)
    1 - Seaswirl oscillating water direction device (set to always on)
    1 - Reeflo Dart supergold water pump (set to always on)

  6. #16
    Join Date
    19.02.2009
    Posts
    2,976

    Default

    We built the same configuration and we have no problem to calibrate.

    Maybe the ExpansionBox is not correctly assigned.

    Try following:
    ProfiLux -> System -> Configure PAB -> PAB Systemreset
    And then assign the ExpansionBox and the two Powerbars again.

    Is the problem still there?

  7. #17
    Join Date
    13.12.2009
    Location
    Alberta, Canada
    Posts
    72

    Default

    Thank you.
    I'll be able to try that later tonight.

  8. #18
    Join Date
    13.12.2009
    Location
    Alberta, Canada
    Posts
    72

    Default

    Yes, that seems to get things working again.

    Thank you.

  9. #19
    Join Date
    21.11.2011
    Location
    manchester
    Posts
    108

    Default

    I am about to calibrate my redox probe but am wondering what the null plug is?

  10. #20
    Join Date
    13.12.2009
    Location
    Alberta, Canada
    Posts
    72

    Default

    The null plug is a probe connector that has a metal stub instead of a wire leading to a probe. It gets plugged into your Profilux unit in place of your redox probe.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •