Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Arcadia Eco-Aqua LED Lamps and LEDControl???

  1. #1
    Join Date
    22.10.2010
    Location
    Netherlands
    Posts
    224

    Default Arcadia Eco-Aqua LED Lamps and LEDControl???

    Hello there,

    Is it possible to connect the Arcadia Eco-Aqua LED Lamps to the Profilux3 so that the are dimmable. Can i perhaps do this by connecting the Arcadia LED-tubes to a GHL LEDControl1 of LEDControl4?? The Arcadia LED-tubes are a great product, but for now they are connected through the GHL-powerbar, and thus can be only switched on or off. It would be great if the were dimmable.

    I did e-mail Arcadia about some information, but the gave no reponse.
    On the Internet i couldn't find any information either.
    Perhaps you at GHL can help me with this question.

    This is the link to the Arcadia Eco-Aqua LED tubes.

    With Kind Regards,
    Jack

  2. #2
    Join Date
    22.10.2010
    Location
    Netherlands
    Posts
    224

    Default

    No response jet, so it's apparently a difficult question.
    Perhaps that a few photo's from the inside of the driver will help.

    So witch expert out there, can figure out from the pictures which type of GHL LEDControl I need to dimm the Arcadia Eco-LED lamps.
    Or is it perhaps not possible?

    Any help will be appreciated......

    Greetings,
    Jack
    IMG_5124.jpgIMG_5125.jpgIMG_5126.jpgIMG_5128.jpgIMG_5130.jpg

  3. #3
    Join Date
    22.10.2010
    Location
    Netherlands
    Posts
    224

  4. #4
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    it seems they work with 24V, the LEDControl4Active is able to deal with voltages up to 18V

    and I am not sure if they work with a constant voltage (then resistors in the tube are required) or with a constant current

    -> I don`t think this will work, but I have too less technical details
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #5
    Join Date
    22.10.2010
    Location
    Netherlands
    Posts
    224

    Default

    That's to bad...........
    So, at this time there is no way to get the Profilux dimm the Arcadia ECO-LED lamps?
    Time for you to make a LEDControl5, especially for me and mij Arcadia LED lamps

    Or is there a way to modify the existing LEDControl's for my purpose?

    Greetings Jack

  6. #6
    Join Date
    19.02.2009
    Posts
    2,976

    Default

    Unfortunately the design only allows up to 18V.
    To achieve higher voltages the circuit of LEDControl4 have to be changed.

  7. #7
    Join Date
    22.10.2010
    Location
    Netherlands
    Posts
    224

    Default

    I found this thing on the Internet........ can i connect the 0-10v interface on this LEDDriver to the 0-10v interface on the Profilux? Or is it a different kind of interface.
    (And yes...i know if my Led Lamps don't work with a constant voltage, something might blow up..)

    ledvoedingdimmer3.jpg
    Last edited by mdanielse; 12.03.2011 at 14:20.

  8. #8
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    I can`t read the datasheet, too small resolution

    but a standard 0-10V-input can of course be driven by Profilux
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  9. #9
    Join Date
    22.10.2010
    Location
    Netherlands
    Posts
    224

    Default

    I hope that this closeup is readable...

    Quote Originally Posted by Matthias View Post
    I can`t read the datasheet, too small resolution
    ledvoedingdimmer_closeup.jpg

  10. #10
    Join Date
    19.02.2009
    Posts
    2,976

    Default

    It has a standard 0-10V interface -> so ProfiLux could control it via a L-Port.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •