Connecting Giesemann Matrix plus to Profilux II Light

[clarkii]

Dear support, I am thinking to buy Giesemann's Matrix plus (with LED + 3 pairs of T5 tubes with dimmable ballast (GHL ready)). Currently I own Profilux II Light & ProfiluxSimu LED spot light. What extra GHL cable/splitter should I need to buy to connect the 3 dimmable ballasts from the Giesemann light + ProfiluxSimu LED spot light to the 1-10V interfaces on the Profilux II Light? Thanks in advance, Raymond

[GHL Support]

You can connect the ProfiLux Simu Spot directly to one of the L-ports of the ProfiLux Light. The other port could be used for the Giesemann lamp. As you mentioned that the lamp is "GHL ready", there should already be a fitting plug so that you can connect it directly to the L-port.

[clarkii]

You can connect the ProfiLux Simu Spot directly to one of the L-ports of the ProfiLux Light. The other port could be used for the Giesemann lamp. As you mentioned that the lamp is "GHL ready", there should already be a fitting plug so that you can connect it directly to the L-port.

Hi, thanks for the quick reply. The Giesemann Matrix Plus light set will come with 3 pairs of dimmable T5HO tubes, each pair can be dimmed independent of the other two pairs, will it come with just 1 fitting plug or 3 plugs? Thanks, Raymond

[GHL Support]

I think it will rather be more than one plug - but this is a question that only Giesemann can answer you exactly. Please contact them for further details.

[clarkii]

Hi Carolin, checked that the Giesemann Matrix Plus will come with 3 cables with plugs for the 3 dimmable pairs of T5HO tubes. So I am going to have 1 plug from Profilux Simu spot and 3 plugs from the Giesemann light while there is only 2 connectors on my Prolifux II Light. Will I need to buy the GHL Active Splitter or any accessories to support the connectivity? Thanks again, Raymond

[GHL Support]

Hello,
yes, the only possibility is to take indeed the Active-L-Splitter in order to connect the 3 pairs to one L-port.

[clarkii]

Hello, thanks for quick reply, may I further confirm that after adding Active-L-Splitter, the Prolifux II Light will be able to recognize the 4 dimmable units (1 Sun+Moon, 3 pairs of T5HO tubes) and I can program them independently via the control unit itself or the Prolifux software?

Thanks, Raymond

[GHL Support]

Yes, the ProfiLux II Light will recognize all the lamps. The computer provides four 1-10V-interfaces, i.e. 4 independently controllable dim channels (L1L2 and L3L4).
ProfiLux Simu will need for example L1L2 (one channel for blue and one for red LEDs), then you will have (through the Active-L-Splitter) 4x L3L4 available.
I am not definitely sure about this but assume that the 3 cables for the T5 tubes (if they dim the tubes in pairs) will react either to L3 or L4.
So they will all react the same and can't be dimmed separately.

[clarkii]

Hello, I received the Giesemann Matrix Plus light with 3 pairs of dimmable T5 using EVG dimmable ballasts.

It comes with 4 electric plugs for each pairs of T5 and the LED. It also comes with 2 GHL plugs.

I just did some quick checking and testing. The first thing I don't quite understand is the T5 will turn on when I connect the plug directly to wall sockets (not on Profilux II Light) but the GHL plugs are not connected to Profilux II Light yet. Is it normal? How can I proceed to test using the Profilux software which I just installed and can connect to the Profilux II light successfully.

[GHL Support]

Connect the plugs to the 1-10V-interfaces at the Profilux II Light (L-port). In the PC-software (or at the device itself) go to System/1-10V-interfaces and select for example as function Illumination 1 for the belonging interface e.g. L1. Afterwards define a dimming curve under Illumination / Illumination 1, select dimmable lamp and save.