Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: AI control of all 3 channels white, blue, Royal Blue?

  1. #1
    Join Date
    16.06.2009
    Posts
    109

    Default AI control of all 3 channels white, blue, Royal Blue?

    AI has now released the new firmware for their controller to have separate control of all 3 channels...white, blue , royal blue

    when will the profilux be capable of handling the 3 discrete channels?

  2. #2
    Join Date
    28.04.2010
    Posts
    41

    Default

    +1

    I was just going to ask the same question on RC but thought I would check here first.

  3. #3
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    we got feedback from Aqua Illumination - they don't want to give us the technical details before January (no date available so far)

    -> we can't do anything in regards to our firmware at the moment
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  4. #4
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    Has anyone the new 3 channel AI lamp yet?

    if yes - please send me a PM
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #5
    Join Date
    16.06.2009
    Posts
    109

    Default

    pm sent

  6. #6
    Join Date
    08.12.2010
    Posts
    19

    Default

    Hi Mathieus, I have new AI light, can you assist with control of all 3 channels?

  7. #7
    Join Date
    19.02.2009
    Posts
    2,976

    Default

    Please sent a PM to Matthias - thanks.

  8. #8
    Join Date
    08.12.2010
    Posts
    19

    Default

    Done, I have discovered a problem, when I set the Illumination 1 & 2, to 100%, on the Display is only shows 30% & 28%? Is this a bug? Can the light be properly controlled?

  9. #9
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    I don't understand this post
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  10. #10
    Join Date
    08.12.2010
    Posts
    19

    Default

    Hello Matthaius what I'm trying to say if I configure Illumination 1&2 in pcl 5 to 100% & save the configuration to the p3, on the display of the p3 it only shows Ilimination 1&2 at 30% & 28%, I don't see it ever going to 100%. illumination 1 is configured for white led & Illumination 2 is configured for blue led.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •