Page 1 of 3 123 LastLast
Results 1 to 10 of 25

Thread: 10V port schematic

  1. #1
    Join Date
    03.07.2010
    Posts
    44

    Default 10V port schematic

    Please can I get a copy of the 10V port Schematic

    I am looking at a DIY DC pump

  2. #2
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    the easiest way to access the 1-10V-interfaces of the ProfiLux is using the product LBF-AP
    http://www.aquariumcomputer.com/Syst...cessories.html
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #3
    Join Date
    03.07.2010
    Posts
    44

    Default

    Thanks for the info but I am going to be making my own controller & need to know which wires do what on the 10V cable. which is positive & which is neutral?

  4. #4
    Join Date
    10.03.2009
    Posts
    478

    Default

    Pin Function Color
    1 +12V Black
    2 Dimming intensity channel 1 Brown
    3 GND Red
    4 On/off channel 1 (relay control) Orange
    5 Dimming intensity channel 2 Yellow
    6 On/off channel 2 (relay control) Green

    http://www.aquariumcomputer.com/Foru...-EVG-AP-2F-HIC

  5. #5
    Join Date
    03.07.2010
    Posts
    44

    Default

    So I will be using Pin 3 & 2 - I want to change the voltage using these 2 pins to my DIY controller.

    So if I connect my multi meter to the profilux on pin 3 & 2 I will be able to see voltage 0 - 10 when a pump pulses?

    Mark

  6. #6
    Join Date
    10.03.2009
    Posts
    478

    Default

    yes pin 2,3 or 5 depending on the channel you want to use like L1 = 2, L2 = 5, L3 = 2, L4 = 5 etc.

  7. #7
    Join Date
    03.07.2010
    Posts
    44

    Default

    Thank you so much boboxx - so L1 & L2 can be run from one Port & L3 & L4 from another port - IE 1 Port can run 2 x 10v devices

  8. #8
    Join Date
    10.03.2009
    Posts
    478

    Default

    yes thats correct, each L ports have 2 control line

  9. #9
    Join Date
    03.07.2010
    Posts
    44

    Default

    thank you boboxx

    how do I use the relay control? pin 4 "Orange" does is send a signal out is so how many volts? would i connect pin 3 & 4 to a relay to switch it on / off?

    thanks
    Mark

  10. #10
    Join Date
    10.03.2009
    Posts
    478

    Default

    That I'm not sure, but you could mesure it... it probably stays high or low... do not connect them together
    Last edited by boboxx; 28.07.2010 at 20:47.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •