Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: 1-10v port's pin configuration

  1. #1
    Join Date
    20.03.2010
    Posts
    19

    Default 1-10v port's pin configuration

    Hi Matthias

    May I know what is the pins configuration for the 1-10v port for ProfiLux Light controller?

    I need it to connect my dimmable LED driver correctly.

    Please kindly advice.

    Thanks.
    James.

  2. #2
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    Hi James

    the pin assignment can be found in the EVG-AP manual here:
    http://www.aquariumcomputer.com/Down...G-AP2_V400.pdf

  3. #3
    Join Date
    20.03.2010
    Posts
    19

    Default

    Quote Originally Posted by Matthias View Post
    Hi James

    the pin assignment can be found in the EVG-AP manual here:
    http://www.aquariumcomputer.com/Down...G-AP2_V400.pdf
    Which pin should I connected to the dimmable driver's positive and negative dimmer line?

    pin 2 & 3 or 5 & 3 or otherwise?

  4. #4
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    2 & 3 if using channel L1, 5 & 3 if using L2

  5. #5
    Join Date
    20.03.2010
    Posts
    19

    Default

    What is pin 4 & 6 use for ?

  6. #6
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    additional signal for switching off relays at 0% brightness

  7. #7
    Join Date
    30.01.2010
    Location
    Athens
    Posts
    295

    Default

    L1 & L2 goes from 1 telepfone jack.
    Lets say that in that jack there are 6 contacts, starting from left to right numbering 123456 (as in the picture bellow).



    Can you tell me which numbers are:
    +10V for L1
    Grd for L1
    +10V for L2
    Grd for L2

    I want to make the jack so to connect 2 dimmable ballasts to dimm 2 T5 tubes.
    Last edited by almost; 29.03.2010 at 21:02.

    Worlds most gadget Aquarium.. almost.

  8. #8
    Join Date
    07.06.2009
    Posts
    738

    Default

    small remark: L ports only have 4 contacts so your numbering would be 1,2,3,4 :-)

    S ports do have 6 contacts

  9. #9
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    L ports only have 4 contacts so your numbering would be 1,2,3,4 :-)
    - this is not correct - all 6 pins are used for the L-ports

    pin 1 is on the left (view from rear)

  10. #10
    Join Date
    07.06.2009
    Posts
    738

    Default

    Quote Originally Posted by Matthias View Post
    - this is not correct - all 6 pins are used for the L-ports

    pin 1 is on the left (view from rear)
    oops, indeed it are 6 pins , don't now why I was under the impression that it was 4 pins.
    my humble apologies

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •