Results 1 to 4 of 4

Thread: Profilux 4 + Doser 2.1 + ION Director + Deser 2.1

  1. #1
    Join Date
    05.08.2022
    Posts
    3

    Frage Profilux 4 + Doser 2.1 + ION Director + Deser 2.1

    Good morning,
    I need help connecting the Dosing Pump to P4 and ION Director with Dosing Pump. I want to have all devices and their results visible in the Dashboard.

    The ION is connected by a cable to the Doser 2.1.
    The P4 is connected to a second Doser 2.1 pump

    When I go to GHL Connect (Apple iPad) and want to add P4, I enter all the data into the WiFi tip, but it has problems with connection (is it 5g WiFi fault?). Connect via hotspot and enter System shows only one pump out of two, why? After selecting it, I have no option to edit it.

    I also tried to connect to the computer via IP but it did not work.

    And he doesn't even want to think about joining the ION Director?


    Someone has attached such a set and knows how to do it?

    I would be very grateful for your help!

  2. #2
    Join Date
    27.05.2015
    Posts
    2,488

    Default

    Since you have a SA Doser and plan to have the P4 control it, you first needed to set it to slave mode otherwise the P4 cannot control the doser. A master device cannot control another master device. Go back to your PAB page in the P4 settings and press SYSTEM reset to remove this doser from your PAB device list, then disconnect the PAB cable from the SA Doser. Afterwards, connect to your SA Doser via USB or hotspot and set it to slave mode. It would also be good to update all your native SA Doser and P4. Outdated FW will not work with the IOND.

    https://www.aquariumcomputer.com/kno...to-slave-mode/
    https://www.aquariumcomputer.com/kno...oser-firmware/
    https://www.aquariumcomputer.com/kno...ux-4-firmware/

    Once your devices are updated, you can procced with following the IOND setup steps:
    https://www.aquariumcomputer.com/kno...-setup-part-1/

    If you continue to have trouble with this, please open a support ticket for 1-on-1 assistance.
    No support or warranty issues over PM!
    Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.

    Creating a support ticket
    For support or warranty issues, create a support ticket by clicking here.

  3. #3
    Join Date
    05.08.2022
    Posts
    3

    Default

    Quote Originally Posted by Vinny View Post
    Since you have a SA Doser and plan to have the P4 control it, you first needed to set it to slave mode otherwise the P4 cannot control the doser. A master device cannot control another master device. Go back to your PAB page in the P4 settings and press SYSTEM reset to remove this doser from your PAB device list, then disconnect the PAB cable from the SA Doser. Afterwards, connect to your SA Doser via USB or hotspot and set it to slave mode. It would also be good to update all your native SA Doser and P4. Outdated FW will not work with the IOND.

    https://www.aquariumcomputer.com/kno...to-slave-mode/
    https://www.aquariumcomputer.com/kno...oser-firmware/
    https://www.aquariumcomputer.com/kno...ux-4-firmware/

    Once your devices are updated, you can procced with following the IOND setup steps:
    https://www.aquariumcomputer.com/kno...-setup-part-1/

    If you continue to have trouble with this, please open a support ticket for 1-on-1 assistance.
    Thank you for your help. I have two more questions:

    How to make the GHLDEV network show up again ... because you can't see it.

    and

    If there are two SAs, I can only join one because two generate the same network name. I have to turn off one and connect to one and put it into Slave mode and only turn on the other one and do the same, right?

  4. #4
    Join Date
    27.05.2015
    Posts
    2,488

    Default

    Yes, that is correct.

    The ProfiLux troubleshooting article may help you get connected to the GHLDEV network:
    https://www.aquariumcomputer.com/kno...4e-mini-light/
    No support or warranty issues over PM!
    Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.

    Creating a support ticket
    For support or warranty issues, create a support ticket by clicking here.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •