Results 1 to 4 of 4

Thread: Bugfix for Sensor-Performance

  1. #1
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default Bugfix for Sensor-Performance

    ION Director sensor performance is displayed too low

    After the delivery of the ION Director has started, we receive a lot of valuable customer feedback, which helps us to further perfect the ION Director. Even though the ION Director has been extensively tested by us and beta testers, new insights are gained from the end user experience, especially because of the significantly higher number of users by now.

    Due to the now much broader data base, we were able to determine that the so-called "sensor performance", which indicates the state of the sensor, is calculated significantly too pessimistically. It turned out that the electrical sensor characteristic still changes noticeably especially in the first time, this change is also still different from sensor to sensor. However, the sensor remains as accurate as before and keeps the precision according to the technical data of the IOND.
    Now that many more sensors are in real-world use than was possible during the test phase, we can use a large amount of data to optimize the calculation.

    We have thus revised the calculation algorithms of the sensor performance accordingly. As of today, the following updates are available in the download area:
    - GHL Control Center V1.1.3.7
    in it are included:
    - P4 V7.28
    - P3 V6.46
    - Doser V1.40
    Please update GCC and your device to get a realistic sensor performance displayed.

    Furthermore I would like to point out that since 2 weeks there is an update of the ION Director manual, changes were made especially concerning the handling and the preparation of the sensor. If you are still using an older version of the IOND manual please download the latest version.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  2. #2
    Join Date
    11.03.2011
    Posts
    107

    Default bo 1.40

    I installed the 6.46 on my p3 but there is no 1.40 for the doser included.


    Quote Originally Posted by Matthias View Post
    ION Director sensor performance is displayed too low

    After the delivery of the ION Director has started, we receive a lot of valuable customer feedback, which helps us to further perfect the ION Director. Even though the ION Director has been extensively tested by us and beta testers, new insights are gained from the end user experience, especially because of the significantly higher number of users by now.

    Due to the now much broader data base, we were able to determine that the so-called "sensor performance", which indicates the state of the sensor, is calculated significantly too pessimistically. It turned out that the electrical sensor characteristic still changes noticeably especially in the first time, this change is also still different from sensor to sensor. However, the sensor remains as accurate as before and keeps the precision according to the technical data of the IOND.
    Now that many more sensors are in real-world use than was possible during the test phase, we can use a large amount of data to optimize the calculation.

    We have thus revised the calculation algorithms of the sensor performance accordingly. As of today, the following updates are available in the download area:
    - GHL Control Center V1.1.3.7
    in it are included:
    - P4 V7.28
    - P3 V6.46
    - Doser V1.40
    Please update GCC and your device to get a realistic sensor performance displayed.

    Furthermore I would like to point out that since 2 weeks there is an update of the ION Director manual, changes were made especially concerning the handling and the preparation of the sensor. If you are still using an older version of the IOND manual please download the latest version.

  3. #3
    Join Date
    10.10.2013
    Posts
    994

    Default

    Quote Originally Posted by scrub29 View Post
    I installed the 6.46 on my p3 but there is no 1.40 for the doser included.
    1.40 is only for doser SA used in standalone mode.

  4. #4
    Join Date
    11.03.2011
    Posts
    107

    Default

    Quote Originally Posted by itsmorefun View Post
    1.40 is only for doser SA used in standalone mode.
    oke, but my sensor is a month and needs replacement soon. I only have the slave one.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •