Zeige Ergebnis 1 bis 6 von 6

Thema: Oxygen Saturation

  1. #1
    Registriert seit
    10.06.2018
    Beiträge
    19

    Standard Oxygen Saturation

    My O2 saturation is always between 103 and 104 %. I have lots of surface agitation, plus my skimmer so I am always supersaturated. My problem is no matter what I have my settings set to, it always throws the error "Alarm: The measured value has fallen below or exceeded the alarm threshold." So right now, it is 103.8 and throwing the error. My nominal value is set to 100 and my hysteresis is set to 5. I have the alarm set to active and the max deviation is set to +/- 5. Interestingly enough, when I make the alarm inactive, the error still shows. Is this a known issue or am I just stupid?
    Thanks,
    Geändert von Shredded (19.04.2021 um 02:49 Uhr)

  2. #2
    Registriert seit
    27.05.2015
    Beiträge
    2.163

    Standard

    Can you please post a screenshot of your settings?
    If you temporarily disable this sensor port, save changes, then re-enable, does the alarm come back?
    No support or warranty issues over PM!
    Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.

    Creating a support ticket
    For support or warranty issues, create a support ticket by clicking here.

  3. #3
    Registriert seit
    10.06.2018
    Beiträge
    19

    Standard

    Zitat Zitat von Vinny Beitrag anzeigen
    Can you please post a screenshot of your settings?
    If you temporarily disable this sensor port, save changes, then re-enable, does the alarm come back?
    If I disable the sensor, the error goes away. I can save the entry, reboot the app and when I enable the sensor the error returns. See attached screen shots below for settings.
    Angehängte Grafiken Angehängte Grafiken
    Geändert von Shredded (21.04.2021 um 03:44 Uhr)

  4. #4
    Registriert seit
    12.04.2015
    Beiträge
    292

    Standard

    ADC 2 = 980 that is much to high.

  5. #5
    Registriert seit
    10.06.2018
    Beiträge
    19

    Standard

    Zitat Zitat von Gandalf Beitrag anzeigen
    ADC 2 = 980 that is much to high.
    So recalibrate? Obviously you know this from your experience, but what exactly is the alarm/error based on? As a user, I am looking at water parameters that would be out of wack... i.e. Oxygen level that is too low.... something like that, as opposed to a calibration number this is not right, as I would have no way of knowing this. (Not sure that it makes any difference but the reading is 930, I'm assuming either way it is too high)
    Geändert von Shredded (21.04.2021 um 15:23 Uhr)

  6. #6
    Registriert seit
    27.05.2015
    Beiträge
    2.163

    Standard

    Yes, please recalibrate.

    If the issue persists, please create a support ticket and include the above screenshots.
    No support or warranty issues over PM!
    Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.

    Creating a support ticket
    For support or warranty issues, create a support ticket by clicking here.

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •