Zeige Ergebnis 1 bis 7 von 7

Thema: ATO doser turn off through maintenance mode?

  1. #1
    Registriert seit
    17.11.2020
    Beiträge
    13

    Standard ATO doser turn off through maintenance mode?

    Hi

    I have so far setup my ATO with a single optical sensor, which works fine.
    Also setup a maintenance mode which turns of various sockets on the PAB.
    Question is, how do I turn of the ATO / doserpump?
    Do I have to cut the power to the doser, or can I program it to just turn of specific pumps?
    I don't want the ATO to run, if I remove water from the sump

  2. #2
    Registriert seit
    12.04.2015
    Beiträge
    238

    Standard

    yes, but it is a little tricky. use a high unused switch channel set it to a programmable logig. the logig musflt be something like ato and maintanance invertet. the pump must be asignd to the switch channel.

  3. #3
    Registriert seit
    17.11.2020
    Beiträge
    13

    Standard

    Zitat Zitat von Gandalf Beitrag anzeigen
    yes, but it is a little tricky. use a high unused switch channel set it to a programmable logig. the logig musflt be something like ato and maintanance invertet. the pump must be asignd to the switch channel.
    Ok, so I need to do some programmable logic with the switch channel assigned to my ATO.
    I already added some to turn skimmer on 180s later than everything else after maintenance, so might figure out how to do this.
    Thanks.

  4. #4
    Registriert seit
    27.05.2015
    Beiträge
    2.093

    Standard

    If you already have your ATO function setup (D2.1 pump for ATO), you would only need to create 1 Programmable Logic function which combines the existing ATO function with the maintenance mode which shall turn OFF the pump head.

    Do the following:
    1. Go to the PL settings page and select an unused gate
    2. Set the function to AND
    3. Set Input 1 to your current ATO function
    4. Set Input 2 to Maintenance and select the maintenance mode you want the pump head to react to
    5. Set Input 2 to Inverted and save settings
    6. Go to the Switch channels page and select the outlet controlling your Doser 2.1 ATO pump...set the function to Programmable Logic and select the gate number you used when you created the PL function
    7. Save settings

    The above will turn OFF the assigned Doser ATO pump if it happens to be ON when you want to activate this maintenance mode.
    No support or warranty issues over PM!
    Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.

    Creating a support ticket
    For support or warranty issues, create a support ticket by clicking here.

  5. #5
    Registriert seit
    17.11.2020
    Beiträge
    13

    Standard

    Thanks for the reply.
    I already have a PL for my ATO, to run a minimum of 300 sekunds, to avoid it shutting on and off constantly.

    So ATO switch channel is already set to a PL.
    How can I set both PLs to same switch channel?

  6. #6
    Registriert seit
    27.05.2015
    Beiträge
    2.093

    Standard

    Easy.

    Create a new PL function where you select your current PL as Input 1 and the maintenance mode (Inverted) as Input 2.
    No support or warranty issues over PM!
    Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.

    Creating a support ticket
    For support or warranty issues, create a support ticket by clicking here.

  7. #7
    Registriert seit
    17.11.2020
    Beiträge
    13

    Standard

    I thought that might work. Thanks

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •