Results 1 to 5 of 5

Thread: Doser 2.1 - Question on Add-On control and Caluclated Adjustment

  1. #1
    Join Date
    30.06.2020
    Posts
    8

    Default Doser 2.1 - Question on Add-On control and Caluclated Adjustment

    Hello,

    Quick question regarding the Calculated Adjustment per dosing value located on the dosing pump overview.

    I have noticed that after a sucessfull test with the KHD the Calculated Adjustment per dosing shows a value of "0".
    However, the individual dosing times do show an Adjustment rate of "1.0" ml which clearly indicates that an extra ml was added to the dosing schedule in order to compensate for the latest KH test.
    Please note, the target value for the KH is 8dKH and the test result was 7.6.

    Following the above, shouldnt the Calculated Adjustment value also show 1ml instead of 0? If not, would it be possible for someone to explain when this value is actually changed?

    Any clarification here is deeply appreciated. Thanks in advance.
    Attached Images Attached Images

  2. #2
    Join Date
    09.11.2017
    Posts
    1,476

    Default

    The adjusted rate shows the normal dosing +- the adjustment. In your case the calculated adjustment is 0.
    Please note that the adjustment is first calculated after the first measurement after you've configured the control settings.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #3
    Join Date
    30.06.2020
    Posts
    8

    Default

    Quote Originally Posted by Thilo View Post
    The adjusted rate shows the normal dosing +- the adjustment. In your case the calculated adjustment is 0.
    Please note that the adjustment is first calculated after the first measurement after you've configured the control settings.
    Hi, thanks for the quick reply.
    So just to verify, the adjusted rate shows the amout of ml already added on the dosings while the calculated adjustment shows the amount that was added on the adjusted rate after the latest KHD test?

    As an example:

    Assuming that the current KH value sits at 7.6 and the current adjustment rate is 1"ml"

    Perform a KHD test -> Results in 7.6 -> Calculated Adjustment is "0"ml and adjustment rate is 1"ml"

    Perform a KHD test -> Results in 7.0 -> Calculate Adjustment is "1"ml and adjustment rate is now 2"ml"

    Is this correct?

    Thanks in advance.

  4. #4
    Join Date
    09.11.2017
    Posts
    1,476

    Default

    Yes, the 'Calculated adjustment per dosing' shows the calulated adjustment of the control and the 'Adjusted rate' shows the total amount (incl. adjustment) that will be dosed until the next KH measurement.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #5
    Join Date
    30.06.2020
    Posts
    8

    Default

    Quote Originally Posted by Thilo View Post
    Yes, the 'Calculated adjustment per dosing' shows the calulated adjustment of the control and the 'Adjusted rate' shows the total amount (incl. adjustment) that will be dosed until the next KH measurement.
    Ok, crystal clear now, thank you so much for the assistance.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •