Zeige Ergebnis 1 bis 8 von 8

Thema: Aquatic Hybird DX18 dimmable

  1. #1
    Registriert seit
    30.05.2011
    Beiträge
    36

    Standard Aquatic Hybird DX18 dimmable

    Hi may I know what kind of cable of 0-10v should I order if want control Aquatic hybrid dx18 from GHL ? Below is dx18 dimmable adaptor (3.5mm)

  2. #2
    Registriert seit
    12.08.2019
    Beiträge
    2

    Standard

    We modified one of our older Archon controller wires to create a wire for the Profilux Mini we are using at the office.

    With the 3.5 male stereo cable the back section of the wire is ground, the middle and tip are the two 0 -10 V outputs. We then placed the wires in a phone jack connector with position 2 white wire (+), position 3 black (-) and position 5 red (+).

    Pin placement.png
    IMG_2080.jpg
    IMG_2081.jpg
    Angehängte Grafiken Angehängte Grafiken
    Geändert von AquaticLifeProducts (12.08.2019 um 22:26 Uhr)

  3. #3
    Registriert seit
    30.05.2011
    Beiträge
    36

    Standard

    Thanks your info.

  4. #4
    Registriert seit
    30.05.2011
    Beiträge
    36

    Standard



    DIY cable is able to control, but not able completely shutdown dx18 when scheduler is running at 0%, may I know if there anything else need to set it from GHL P4 ?

  5. #5
    Registriert seit
    12.08.2019
    Beiträge
    2

    Standard

    Zitat Zitat von whoami Beitrag anzeigen


    DIY cable is able to control, but not able completely shutdown dx18 when scheduler is running at 0%, may I know if there anything else need to set it from GHL P4 ?
    Yes that is correct the HEP ballast dim to 2% at 0 V input. I have the power cord of the fixture also timed on one of the GHL controlled outlets.

  6. #6
    Registriert seit
    13.08.2010
    Beiträge
    3.748

    Standard

    You can alternatively connect an EVG-AP-2F-HIC in between, so the lamp will be completely disconnected from the power line.

    regards Pit

  7. #7
    Registriert seit
    28.08.2019
    Beiträge
    16

    Standard

    Zitat Zitat von AquaticLifeProducts Beitrag anzeigen
    We modified one of our older Archon controller wires to create a wire for the Profilux Mini we are using at the office.

    With the 3.5 male stereo cable the back section of the wire is ground, the middle and tip are the two 0 -10 V outputs. We then placed the wires in a phone jack connector with position 2 white wire (+), position 3 black (-) and position 5 red (+).

    Pin placement.png
    IMG_2080.jpg
    IMG_2081.jpg

    Is DIY the only option? I have a kessil-to-apex cable I no longer need so I was planned on using that. Until I realized the yellow p4 ports are not the same. I have 2 (eventually 3) Aquatic Life DX18s... surely GHL or AI sell a compatible cable?

  8. #8
    Registriert seit
    27.05.2015
    Beiträge
    1.545

    Standard

    You can still use that apex cable by cutting the RJ45-end and connecting the two wires to our Breakout box accessory. This accessory then connects directly to the 1-10V port on the ProfiLux.

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •