Results 1 to 4 of 4

Thread: Kh director technical setup advice

  1. #1
    Join Date
    02.08.2019
    Posts
    2

    Default Kh director technical setup advice

    Hello,
    I'm just about to start a new GHL setup in my 600 L SPS/LPS tank for Balling, and since I'm pretty new to the GHL hardware and can't find an obvious answer I let myself to start a new topic.

    1) I want to go a Kh Director with a two pumps and profilux 4. Will a profi 4e will be sufficient for such setup or should I go p4? (I would rather get access to charts and online access that is availavle through P4 and not in SA version)
    2) Is there specific country version with F/B cables available (Poland user here)? Or should I better get an adapter for Schuko
    3) Connection of hardware.

    My Balling liquids are 4 metres away from main tank and for now liquids are distributed by automatic pumps located at the liquids (suction distance Ca 30cm and pushing distance approximately 3m). I want to locate KhD, 1 GHL doser 2.1 and p4 close to the tank (~30cm), and the other GHLS 2.1 doser at liquids (~3m away). How do I connect devices? Do i need one PAB cable of 5m length (to connect "liquid" pump to p4) lor two (to connect KhD to "liquid" pump and then back to p4?
    So the question is whether which device should be connected to which one - A: KhD to pump (1) and pumps (1) and (2) to p4 or rather than B: KgD to pump (1), pump (1) to pump (2) and pump (2) to p4?

    In A setup i assume I would use one long PAB cable, in scenario B I need to get two.


    Thanks in advance!

  2. #2
    Join Date
    09.11.2017
    Posts
    1,476

    Default

    Hi,

    the ProfiLux 4e would be sufficient for this. But the SA Doser can also be connected to the myGHL-cloud and the charts will be available soon.

    There are specific country versions, including a Schuko version.

    The PAB connections are connected in series, the order does not matter. Scenario B would therefore be correct.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #3
    Join Date
    02.08.2019
    Posts
    2

    Default

    Thanks for clarification!

    I just cant find an answer whether the kH Director is produced fot type F/B plug (French type which is used in Poland),

    in the store there is no F/B type, thats why i asked if I should more likely use custom adapter or custom power cable? Probably I am overcomplicating this (as I did before I knew the connection order did not matter)

    https://store.aquariumcomputer.com/e...r-2-1-set.html
    Last edited by Yogher; 08.08.2019 at 10:25.

  4. #4
    Join Date
    09.11.2017
    Posts
    1,476

    Default

    Yes, the "DE, Schuko" version will fit.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •