Zeige Ergebnis 1 bis 8 von 8

Thema: Doser 2

  1. #1
    Registriert seit
    19.08.2018
    Beiträge
    6

    Standard Doser 2

    Since I’ve had my doser 2 it’s always had the ghl logo blinking red which means alarm
    I’ve been told to check the alarm condition of Any pump. And water sensor is met
    WHAT DOES THIS MEAN
    Then I’ve been told to pab system reset and reasign any devices
    The only cable I have is the USB one that came with the doser which was second hand
    How do I stop the logo from flashing red


    Sent from my iPhone using Tapatalk

  2. #2
    Registriert seit
    20.05.2017
    Beiträge
    58

    Standard

    Is it a standalone or attached to Profilux?

    Sent from my SM-N950F using Tapatalk

  3. #3
    Registriert seit
    19.08.2018
    Beiträge
    6

    Standard

    Zitat Zitat von ispookie666 Beitrag anzeigen
    Is it a standalone or attached to Profilux?

    Sent from my SM-N950F using Tapatalk
    It’s a stand-alone doser 2 sa
    Ispookie



    Sent from my iPhone using Tapatalk

  4. #4
    Registriert seit
    20.05.2017
    Beiträge
    58

    Standard

    Either way
    Check the filling level in dosers from 1-16 (even if you are not using them).

    Next look how the dosing pumps are controlled - is it dosing schedule or switch channel ?

    PABcom error normally shows up.

    Sent from my SM-N950F using Tapatalk

  5. #5
    Registriert seit
    19.08.2018
    Beiträge
    6

    Standard

    Zitat Zitat von ispookie666 Beitrag anzeigen
    Either way
    Check the filling level in dosers from 1-16 (even if you are not using them).

    Next look how the dosing pumps are controlled - is it dosing schedule or switch channel ?

    PABcom error normally shows up.

    Sent from my SM-N950F using Tapatalk
    All dosing pumps are controlled by dosing shedule


    Sent from my iPhone using Tapatalk

  6. #6
    Registriert seit
    27.05.2015
    Beiträge
    1.500

    Standard

    An alarm on a Standalone doser is commonly caused by fluid container levels running low or ATO/AWC function time limit being exceeded.
    Solution: Go through each dosing pump channel and click refill container where necessary.

  7. #7
    Registriert seit
    19.08.2018
    Beiträge
    6

    Standard Doser 2

    Zitat Zitat von Vinny Beitrag anzeigen
    An alarm on a Standalone doser is commonly caused by fluid container levels running low or ATO/AWC function time limit being exceeded.
    Solution: Go through each dosing pump channel and click refill container where necessary.
    Done that still the same
    This is getting beyond a joke
    All the tech help I’ve received and the problem still exists

    Sent from my iPhone using Tapatalk
    Geändert von chrisbascombe1 (24.07.2019 um 22:49 Uhr)

  8. #8
    Registriert seit
    27.05.2015
    Beiträge
    1.500

    Standard

    We will need more information to better assist you.


    Did you connect via the app to see what is causing the alarm?
    The app gives you this information.

    Did you go through each dosing channel and refill all containers?

    Do you have any other dosing units connected to this SA doser?
    * If a PAB-cable is disconnected, this will cause the alarm

    Do you have any ATO or AWC functions setup?
    * If a float or optical sensor becomes lose or detached from the port, an alarm will be activated
    Geändert von Vinny (25.07.2019 um 20:25 Uhr)

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •