Seite 1 von 2 12 LetzteLetzte
Zeige Ergebnis 1 bis 10 von 20

Thema: Octo (Reef Octopus) wave and return pumps control

  1. #1
    Registriert seit
    26.11.2016
    Beiträge
    4

    Standard Octo (Reef Octopus) wave and return pumps control

    Purchased Octo Pulse 4 wave pumps which are Apex Ready with 0-10V port, is it possible to control them using Profilux 4?

    The standalone controller only allows 30% to 100% power.

    Any Reef Octopus users?

  2. #2
    Registriert seit
    13.08.2010
    Beiträge
    3.740

    Standard

    Hi boshkg
    is it possible to control them using Profilux 4
    yes

    Octo Pulse 2und 4_ 1-10V Anschluss4.png

    regards Pit

  3. #3
    Registriert seit
    26.11.2016
    Beiträge
    4

    Standard

    Thanks for the quick reply. So this 0-10V cable can be purchased through GHL and it plugs straight into the back of the Profilux 4 or do I need a module similar to the GHL Vortech module?

  4. #4
    Registriert seit
    13.08.2010
    Beiträge
    3.740

    Standard

    A suitable cable is not available directly from GHL
    There are several ways to connect the pump to the Profilux
    1:
    You buy a cable with RJ12 plug 6p6c and install the audio plug on one side.
    2:
    you buy a cable with the audio plug, and connect it with a 6p6c RJ12 plug.
    3:
    You buy a cable with the audio plug and connect it to a (LBF-AP) (PL-0067) if you can buy another one

    RJ12 Steckerbelegun L-Schnittstellen.jpg

    regards pit

  5. #5
    Registriert seit
    26.11.2016
    Beiträge
    4

    Standard

    Thank you.
    So with both pumps connected to the Profilux, I can program them at any % power and to operate in sync or anti-sync (mirror) ?

  6. #6
    Registriert seit
    13.08.2010
    Beiträge
    3.740

    Standard

    Yes, with all the features the Profilux offers. You may have to increase Umin at the 1-10V settings. You have to try ~2.4V.

    regards Pit

  7. #7
    Registriert seit
    26.12.2018
    Beiträge
    11

    Standard

    I have an audio splitter cable - 3.5mm that goes from a female connection into two audio plugs.

    Inside there are four cables and they are very thin and appear to be red, blue, sort of yellow and green.

    Does anyone have any idea about how those would fit into a RJ12 to provide control over two Reef Octopus pumps?

  8. #8
    Registriert seit
    13.08.2010
    Beiträge
    3.740

    Standard

    You can use the new S-Port & L-Port Breakout Box (S-L-Port-BoB)

    regards Pit

  9. #9
    Registriert seit
    26.12.2018
    Beiträge
    11

    Standard

    Thanks Pit, I am aware of that. I still wouldn't know what wire goes where so what's the difference between attaching an RJ12 or using that box?

    If you or someone else could help me with the question then that would be great.

  10. #10
    Registriert seit
    27.05.2015
    Beiträge
    1.511

    Standard

    The breakout box basically fills the incompatibility gap between the communication cable and the ProfiLux. If there is no dedicated GHL communication cable, users will still be able to control their 1-10V devices by connecting which ever communication cable to this breakout box. The other-end of this com cable is then connected to the port on the 1-10V device itself.

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •