Zeige Ergebnis 1 bis 5 von 5

Thema: Lots of questions

  1. #1
    Registriert seit
    20.01.2018
    Beiträge
    2

    Standard Lots of questions

    Question 1: My tank is 89"x24" (23" top to bottom). Do I need 3x or 4x LX7206 light fixtures?

    Question 2: I have 2x VarioS 8 pumps that support a 0-10V interface. What connector do I need to hook them up? I obviously need a YL2-1 splitter cable, but I don't know what else I need.

    Question 3: Can I put a PLM-PWC, PLM-pH/Redox-2Level, and a PLM-pH/Redox in a Profilux 4 all at once?

    Question 4: What does is the advantage of the Measurement Cell vs the Sensorholder 4?

    Question 5: What kind of flow rate should go through the Measurement Cell?

  2. #2
    Registriert seit
    13.08.2010
    Beiträge
    3.645

    Standard

    Question 1: My tank is 89"x24" (23" top to bottom). Do I need 3x or 4x LX7206 light fixtures?
    3 for longitudinal mounting
    Question 2: I have 2x VarioS 8 pumps that support a 0-10V interface. What connector do I need to hook them up? I obviously need a YL2-1 splitter cable, but I don't know what else I need
    You can take an LBF-AP to use both pumps.
    Question 3: Can I put a PLM-PWC, PLM-pH/Redox-2Level, and a PLM-pH/Redox in a Profilux 4 all at once?
    yes, you can plug in all three extension cards
    Question 4: What does is the advantage of the Measurement Cell vs the Sensorholder 4?
    Question 5: What kind of flow rate should go through the Measurement Cell?
    Better inflow of the probes, self-cleaning of the probes, longer service life of the probes. The measuring cell is pressureless, if necessary via bypass into the return flow.

    regards Pit

  3. #3
    Registriert seit
    20.01.2018
    Beiträge
    2

    Standard

    To clarify, I would use a single LBF-AP and would not need the YL2-1 splitter cable, correct?


    Also, do you have an application note or anything about how to plumb the Measurement Cell into a system?

  4. #4
    Registriert seit
    13.08.2010
    Beiträge
    3.645

    Standard

    To clarify, I would use a single LBF-AP and would not need the YL2-1 splitter cable, correct?
    yes
    Also, do you have an application note or anything about how to plumb the Measurement Cell into a system?
    just a simple self-made drawing

    Messzelle.jpg

    regards Pit

  5. #5
    Registriert seit
    27.05.2015
    Beiträge
    1.472

    Standard

    Hi there,

    Question 1: My tank is 89"x24" (23" top to bottom). Do I need 3x or 4x LX7206 light fixtures?
    This is going to depend on what types of coral you plan to keep and how you will position each fixture; parallel or perpendicular to the tank.

    (Perpendicular)
    If you have or will have an SPS dominant reef, 5 fixtures would be ideal for the most even light distribution throughout the whole space.
    If a mixed reef, 4 fixtures are recommended.

    (Parallel or Long way)
    SPS dominant: 4 fixtures
    Mixed reef: 3 fixtures


    Question 2: I have 2x VarioS 8 pumps that support a 0-10V interface. What connector do I need to hook them up? I obviously need a YL2-1 splitter cable, but I don't know what else I need.
    You would need a 1-10V Breakout box from GHL and the control cable from Coralvue. The RJ45-end of this cable would be cut and installed onto the GHL accessory. Once connected, you will be able to individually control the flow of these pumps.


    Question 3: Can I put a PLM-PWC, PLM-pH/Redox-2Level, and a PLM-pH/Redox in a Profilux 4 all at once?
    Yes.
    The P4 includes a total of 3 expansion card slots; 1 slot is for "internal use" which is where you'd connect the PLM-PWC card. The other 2 slots can be for the other cards.


    Question 4: What does is the advantage of the Measurement Cell vs the Sensorholder 4?
    Measurement cell provides an isolated area which allows for a more constant flow rate and is plumbed into your system, usually in a bypass.
    The Sensorholder4 is a magnetic mount that holds the probes out in the open in your sump.


    Question 5: What kind of flow rate should go through the Measurement Cell?
    A slower flow rate is ideal for this accessory.

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •