Do you find the probleme Matthias?
Do you find the probleme Matthias?
The pumps are working when you dose manually from the ProfiLux 3 (not from the Doser) in GHL Control Center?
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
my pumps are 1,2,3 and can dose from the "Dose now" button in GCC. i also calibrated the pumps and seemed to be fine. pump two came out at 6ml flow rate (on slow) for the reagent not sure if that is normal?
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
just to be sure: your P3 is updated to firmware 6.32 and you use GCC1.1.1.0?
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
GCC 1.1.1.0 2018-01-24
***** System report *****
Controller properties
Name: ProfiLux 3.1T eX
Firmwareversion: 6,32
Device address: 2
PAB address: 17
Slot count: 3
Level inputs: 4
Sensor 1: pH-value
Sensor 2: Temperature
Sensor 3: Conduct.(S)
Sensor 4: Redox
Onboard 1-10V outputs: 6
Onboard socket outputs: 8
Slot/card properties
Slot number 0
Name: SERIAL
Class: Communication card
Slot number 1
Name: 2L4S
Class: Intelligent card
Firmwareversion: 1,00
1-10V outputs: 2
Socket outputs: 4
Slot number 2
Name: PWC
Class: Communication card
PAB devices
Name: SMS-Module
Firmwareversion: 3,04
PAB-address: 19
Name: Expansion Box
Firmwareversion: 1,08
PAB-address: 18
Name: VorTech-Controller
Firmwareversion: 1,04
PAB-address: 20
Name: ProfiLux Touch
Firmwareversion: 1,06
PAB-address: 21
Name: GHL Doser 2 Slave
Firmwareversion: 1,27
PAB-address: 22
Name: GHL Doser 2 Slave
Firmwareversion: 1,27
PAB-address: 23
Name: KH Director
Firmwareversion: 1,00
PAB-address: 24
***** System report *****
Controller properties
Name: ProfiLux 3.1N eX
Firmwareversion: 6.32
Device address: 1
PAB address: 17
Serialnumber: 1210063001
Slot count: 3
Level inputs: 4
Sensor 1: pH-value
Sensor 2: Temperature
Sensor 3: Conduct.(S)
Sensor 4: Redox
Onboard 1-10V outputs: 6
Onboard socket outputs: 8
Slot/card properties
Slot number 0
Name: SERIAL
Class: Communication card
Slot number 1
Name: PWC
Class: Communication card
Slot number 2
none
PAB devices
Name: VorTech-Controller
Firmwareversion: 1.03
PAB-address: 19
Serialnumber: 1008056024
Name: Powerbar 6
Firmwareversion: 1.08
PAB-address: 18
Serialnumber: 1207054072
Name: ProfiLux Touch
Firmwareversion: 1.06
PAB-address: 20
Serialnumber: 1207057055
Name: GHL Doser 2 Slave
Firmwareversion: 1.27
PAB-address: 22
Serialnumber: 1801082017
Name: KH Director
Firmwareversion: 1.00
PAB-address: 21
Serialnumber: 1801088054
just updated to GCC 1.1.1.0 and it is still the same. buttons change from grey to blue when I click them but no response from the doser or KHD
What can we do to help GHL to diagnose the problem?
Someone has KH Director successfully working with P3?
Thank
Bookmarks