Zeige Ergebnis 1 bis 5 von 5

Thema: Email setup for Profilux4 Sockets

  1. #1
    Registriert seit
    01.04.2017
    Beiträge
    58

    Standard Email setup for Profilux4 Sockets

    Its nice to get periodic email with the status of the sockets.

    But is there posible to get the discription for the sockets in the email as well ?
    And the current that each socket is using ?
    And is there possible to get the status for all sockets ? I have 23 sockets

    Something like this:
    Code:
    S 1 : On returnpump 0.3A
    The message i recive now:

    Profilux4 Sockets
    S 1 : On
    S 2 : On
    S 3 : On
    S 4 : Off
    S 5 : On
    S 6 : On
    S 7 : On
    S 8 : On
    S 9 : On
    S10 : On
    S11 : On
    S12 : On
    S13 : On
    S14 : On
    S15 : On
    S16 : Off
    S17 : On
    S18 : Off
    S19 : Off
    S20 : Off
    S21 : On
    S22

  2. #2
    Registriert seit
    07.02.2017
    Beiträge
    26

    Standard

    Zitat Zitat von Vega77 Beitrag anzeigen
    Its nice to get periodic email with the status of the sockets.

    But is there posible to get the discription for the sockets in the email as well ?
    And the current that each socket is using ?
    And is there possible to get the status for all sockets ? I have 23 sockets

    Something like this:
    Code:
    S 1 : On returnpump 0.3A
    The message i receive now:
    Yes, below is what I receive via e-mail for sockets. I could not get the "loop" function to work, so I had to code each socket. I also was unable to get values for amps. Maybe these bugs are fixed in the most recent update. I'll give the loop and amps a try again when I get time and will post if successful.

    VSV Off
    Ca Rev. Off
    Heater 1 Off
    Heater 2 Off
    CaOH ATO Off
    180 return On
    55 return On
    Refugium light On
    Fan On
    CO2 On
    þ

    Coding:

    $$SWID[0]$$ $$SWIS[0]$$
    $$SWID[1]$$ $$SWIS[1]$$
    $$SWID[2]$$ $$SWIS[2]$$
    $$SWID[3]$$ $$SWIS[3]$$
    $$SWID[4]$$ $$SWIS[4]$$
    $$SWID[5]$$ $$SWIS[5]$$
    $$SWID[6]$$ $$SWIS[6]$$
    $$SWID[7]$$ $$SWIS[7]$$
    $$SWID[8]$$ $$SWIS[8]$$
    $$SWID[9]$$ $$SWIS[9]$$

    Best Regards, Bob

  3. #3
    Registriert seit
    07.02.2017
    Beiträge
    26

    Standard

    Zitat Zitat von Vega77 Beitrag anzeigen
    Its nice to get periodic email with the status of the sockets.

    But is there posible to get the discription for the sockets in the email as well ?
    And the current that each socket is using ?
    And is there possible to get the status for all sockets ? I have 23 sockets

    Something like this:
    Code:
    S 1 : On returnpump 0.3A
    The message i recive now:


    I used this attached document for coding. note it could be outdated.

    Bob

    User-designed-web-pages-for-ProfiLux-3-3.1.pdf

  4. #4
    Registriert seit
    09.11.2016
    Beiträge
    90

    Standard

    I didn't know anything about that docment and just had some basic stuff setup. I have now messed with it and it seems to work but the email length (not just the legth in GCC is quite limiting. So I have several emails:

    1. Switch states

    Switch states on $$DATE$$ at $$TIME$$

    $$REPS[10][2]$$ $$SWID[x]$$ : $$SWIS[x]$$
    $$REPE$$

    2. Probe values

    Probe Values on $$DATE$$ at $$TIME$$

    $$REPS[5][0]$$ $$SENN[x]$$ : $$SENV[x]$$
    $$REPE$$


    3. Alarms (incl probe values)
    * * * A L A R M - $$DATE$$ at $$TIME$$ * * *

    $$REPS[10][5]$$ Alarm $$LCTR$$: $$ALMS[x]$$
    $$REPE$$

    $$REPS[5][0]$$ $$SENN[x]$$ : $$SENV[x]$$
    $$REPE$$

    I have a duplicate of the switches email set to also send in the event of an alarm so I should get alarms, probes and switches in the event of an alarm.

  5. #5
    Registriert seit
    04.11.2017
    Beiträge
    20

    Standard

    Thanks very much for the coding document Bstohrer. It is very useful. I can now get much more useful information from my emails on P4.



Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •