good work Matthias just hope they are not to costly as its looking like i may need 6 (4 for the tunze and 2 for the meanwells)
good work Matthias just hope they are not to costly as its looking like i may need 6 (4 for the tunze and 2 for the meanwells)
Tunze 6105 vs redox - i'm also curious to learn about the findings and solutions.
As JJB requested if someone has his combination, well here i am. I've got two Tunze 6105 and PLIIex with redox and sinse the installation 3 weeks ago my redox values have not move a bit. They are constantly around 239/238 Mv. As discussed ierlier with Matthias, i'm curious to learn what is causing this. note: i've just started to implant bacteria in the tank, solely holding dead coral and 20 kilo's of life rock. Although the skimmer is already producing waste, i would expect that the redox would respond,. nothing thus.
JJB and Matthias what is the current status now wrt both the redox and 6105's from your previous discussions:
note 2: My PL is seperated from the cabinet with other powercables to ensure/limit interference, so the redox cable goes directly to the probe holder in the tank not meeting any other cable other than the PH, temp and COND cables from the PL. Any suggestions?
Gr. Franklin
what are the redox ADC value?
what does the reading when the probe is immersed in a glas of water outside the tank?
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
Hi Matthias,
Values: according PLControl 5.01.1.1
val1 0mV ADC 468
val2 250mV ADC 564
Tankvalue= 239
with normal tapwater: 289mV after 5 min.
with osmose water: 273mV after 5 min.
then back in tank: 224mV after 5 min.
conclusion?
Gr. Franklin
Hi Matthias, just came across this thread as I'm experiencing the same problems as jjb! Do you have an update on the isolator your working on please?
can any one confirm if changing to a new probe will solve this out standing problem
We found out that all issues with bad probe readings (in most cases redox, in rare cases pH and cond.) had been produced through other devices or bad probes, as far as I know all issues had been solved.
In my opinion an isolator is pointless, for this this reason the development and production (which costs a lot of money initially) hasn`t a high priority anymore at the moment.
This could help:
- if the probe is defective (too old) replace it
- if you have an ungrounded ProfiLux power supply the use of a grounded power supply may help to eliminate the interferences from the Tunze pumps (the latest ProfiLux are shipped with a grounded PSU as standard in order to get rid of problems with noise from 3rd party products)
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
hi Matthias
the probe is about 9 months old so don't want to replace if i don't have to.
please can you let me know about the new grounded power supply and how to get one. i have just got a new dosing unit is the power supply that comes with that the new type.
You can receive the grounded power supply through your retailer, it is:
Spare-AC/DC-EUR
Ersatz Netzteil Europa, Tischnetzteil incl. Netzkabel
Bookmarks