Hi all..my p4 say "new" firmware available on his general page of GCC.
i go to system to start firmware update but click on button but never happen..
if i try to update touch or vortech controller update start correctly.
any ideas?
Hi all..my p4 say "new" firmware available on his general page of GCC.
i go to system to start firmware update but click on button but never happen..
if i try to update touch or vortech controller update start correctly.
any ideas?
I think the System page is for updating firmware of attached devices and not the P4. Go to "Extras" at the top of the page and click. To the left on the toolbar you will see "Firmware Update". Be sure tour PC is connected to the P4 via USB, then click on it.
That worked for me.
Bob
Steps for updating the ProfiLux 4 firmware can be seen here:
https://youtu.be/Fj0SH93QoKc
It certainly CAN work. I was a bit worried as the previous version was unable to save settings. Thankfully mine upgraded OK. I then instantly with the new version saved my settings.
All good so far. Sorry for your pain.
How long does it take to upgrade?
Enviado desde mi Nexus 5 mediante Tapatalk
Later I tried with another laptop, when I pressed accept the laptop disconnected the usb and seemed to work, but it was worse, profilux 4 did not start.
Finally, I had to do it for emergency with the Flash program.
Now I have the latest firmware installed, 7.04
Regards
Enviado desde mi Nexus 5 mediante Tapatalk
No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.
Dear Matthias
I do not mean to be offensive but my experience on the firmware upgrade is somehow different from the videos and I have met some strange situation that I do not know why. Though finally I luckily upgrade the firmware (from 7.03-->7.04, and then 7.04-->7.05), I provide my case for your information for improvement.
1. During the upgrade process (I confirm my Com port is correct and update driver has been chosen), there is a pop up message (after selection of update driver)that instructing me to reset the microcomputer (something else) at the motherboard (something else) but I never find the key to press at P4. (Sorry that this pop up window did not automatic close according to my experience and I need to close it either by yes or no by myself. If I press yes, this will continue and press no the upgrade process will stop)
2. No matter what I do with response to this message (eg : turn off and turn the machine, unplug and replug the usb... and etc), and then I press ok at the pop up box, the upgrade process will continue. After a while, the pop up windows telling me that the upgrade is success and tell me to restart the P4. However, after the restart (turn off and turn on the machine), the firmware is still 7.03. (I have tried many times and the firmware never upgraded.)
3. At last, being told by another user in this forum, I try to delete the 7.03 update driver in the setup directory(i.e. : only the 7.04 file when I upgrade it and only the 7.05 file while I upgrade that), then restart the upgrade process.
4. The pop up window instructs me to reset the microcomputer (or microprocessor or something else) is still appeared after selection of the update file. After a several trials, I finally find that I should just ignore this message (i.e. : doing nothing) but press ok at the pop up windows. Then the upgrade process is really success this time.
These are my experience, I hope that this can help other as well as to provide information to you to make the upgrading step more clear.
By the way, my windows OS is windows 7. (for your reference and information)
Last edited by palmlover; 18.03.2017 at 13:01.
Bookmarks