Doser Gen 1

[Tone]

I have recently purchased a secondhand Gen 1 Slave dosing unit. I have some questions:

(1) What items should be supplied with the unit (ie. when it was new what would GHL have supplied with the unit)?
(2) Where can I find a manual for this dosing pump?

Thanking you in anticipation.

PS. there is nothing about Gen 1 units in the Forums, has it all been purged?

[Vinny]

Hello,

Please take a look at our website's downloads page, you will find what you are looking for there.

https://www.aquariumcomputer.com/dow...r-1-sa-manual/

All the information in the SA version manual except the PROGRAMMING chapter apply to the Slave doser.

[Tone]

Hello,

Please take a look at our website's downloads page, you will find what you are looking for there.

https://www.aquariumcomputer.com/dow...r-1-sa-manual/

All the information in the SA version manual except the PROGRAMMING chapter apply to the Slave doser.

Thank you, Vinny. I have already reviewed that "manuel" [sic] and it imparts no useful information to me ... what cables are used to connect to the Profilux, which port the cable is plugged into, how should the Profilux be programmed, etc. Obviously, the SA version is completely different ? What parts should have originally been included with the Gen slave dosing unit? ;-p

Can anybody else offer any useful suggestions on where the required information can be sourced, please?

[Gunther]

(1) What items should be supplied with the unit (ie. when it was new what would GHL have supplied with the unit)?

• Dosing pump unit with 1, 2, 3 or 4 dosing pumps
• AC/DC adapter
• Cable with westen plug RJ12 (6 lines)

what cables are used to connect to the Profilux

A RJ12 phone cable (ensure it has 6 wires, RJ11 with 6pin socket and 4 wires doesn´t work)

which port the cable is plugged into

S1-4 (or, if you have a PL3 also S5-S8 is possible)

how should the Profilux be programmed

You haven´t told us which PL you have. In any case it depends on your device, the firmware version and the software you use (ProfiluxControl for PLII and GHL Control Center for newer firmware releases of PL3)
Best is to have a look into the Programming guide of your Profilux computer

Obviously, the SA version is completely different ?

Yes, it´s stand-alone only. There is no possibility to connect a Doser 1 SA to a Profilux
It´s simple to check that: The SA version has a display, the slave unit has not.

[Tone]

• Dosing pump unit with 1, 2, 3 or 4 dosing pumps
• AC/DC adapter
• Cable with westen plug RJ12 (6 lines)

A RJ12 phone cable (ensure it has 6 wires, RJ11 with 6pin socket and 4 wires doesn´t work)


S1-4 (or, if you have a PL3 also S5-S8 is possible)


You haven´t told us which PL you have. In any case it depends on your device, the firmware version and the software you use (ProfiluxControl for PLII and GHL Control Center for newer firmware releases of PL3)
Best is to have a look into the Programming guide of your Profilux computer



Yes, it´s stand-alone only. There is no possibility to connect a Doser 1 SA to a Profilux
It´s simple to check that: The SA version has a display, the slave unit has not.

Thank you Gunter!

I have a P3e controller.

At the back of the doser are 2 x RJ jacks, which one is connected to the P3e?

What about the power adaptor, is there any special requirement for its location or can it be plugged into a remote power socket or must it be plugged into a power bar ? I have 2 x digital power bars, how should the socket be set up?

Thank you in anticipation.

[Gunther]

At the back of the doser are 2 x RJ jacks, which one is connected to the P3e?

It doesn´t matter, take one of them. It´s the same as with the power bars.

What about the power adaptor, is there any special requirement for its location or can it be plugged into a remote power socket or must it be plugged into a power bar?

Due it doesn´t make sense to have it switched , put it into an un-switched socket apart from the power bars

I have 2 x digital power bars, how should the socket be set up?

As said: Use an un-switched one.

Remark: The doser is reacts to socket 1-4 if you use S1S4 and to socket 25-28 if you use S5S8 by default.
If you want to change that, unplug the powerbars, plug it into one of the S-socket you want to use (it has to be alone on this socket), change the S-socket to digital and program the doser numbers you want
Programming is similar to the powerbar programming.
If you have done so (switched to digital) it´s possible to daisy-chain the doser with the powerbars.
Ensure that a socket number is not given to two different devices.