Results 1 to 8 of 8

Thread: New GCC 1.0.8.0 and new firmware for ProfiLux 3 and GHL Doser 2

  1. #1
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default New GCC 1.0.8.0 and new firmware for ProfiLux 3 and GHL Doser 2

    New in V1.0.8.0:
    Support for magnetic stirrers, myGHL Read-Only-Access added, other improvements.
    The new features require firmware 6.24 for ProfiLux 3 and firmware 1.16 for GHL Doser 2 (Standalone and Slave) (included in this GCC version).

    https://www.aquariumcomputer.com/dow...enter-v1-0-8-0
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  2. #2
    Join Date
    10.10.2013
    Posts
    994

    Default

    Hello

    Thank but not all is good.

    Firmware upgrade of Doser 2 factory reset ALL settings, ok i recover from settings.par and write back refill container value BUT even wifi go down: My two doser go from AP to client mode... I see Doser 2 wireless network on my computer and dosers are not connected to my wireless network. I had to reapply wifi settings to get them work again.

    Also several problem with Profilux, it lost ALL settings and all sensors history, ok, recover from setting.par and sensor data.par do the trick except lost all sensor history. BUT PROBLEM, now, Constant Flow don't work, Flow sensors settings are set to 0 and change are not keep when close and reopen windows...
    Capture d’écran 2016-02-02 à 23.53.55.png
    What can i do?

    Thank

  3. #3
    Join Date
    10.10.2013
    Posts
    994

    Default

    Hello,

    Can i hope to have some help?

    Thank

  4. #4
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    thank you for your hint

    we examine this flow sensor issue and come back to you ASAP
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  5. #5
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    meanwhile we were are to reproduce this issue and to locate it, GCC doesn't display correctly (the ProfiLux firmware is OK)

    it has been fixed in GCC 1.0.8.1

    we are doing some tests with the new GCC version, we will upload it ASAP
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  6. #6
    Join Date
    10.10.2013
    Posts
    994

    Default

    Ok.

    Thank Matthias :-)

  7. #7
    Join Date
    18.02.2009
    Location
    Kaiserslautern
    Posts
    7,710

    Default

    the update (GHL Control Center 1.0.8.1) is available NOW
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  8. #8
    Join Date
    14.02.2015
    Posts
    30

    Default

    Same (ALL was reset) also happened to me, including all sensors lost calibration which led to my co2 system silently didn't work anymore.
    And what made it worse is that it seems many setting aren't restored correctly from the file i saved with previous firmware. Alarm settings are gone.
    Dosing settings were there but all disabled (listening to input 128 instead of programmed values). etc. :-(
    Last edited by tuxbox; 06.02.2016 at 18:22.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •