Where can I find firmware history?

[Lasse]

I´m working with rather large installations as a professional and a firmware upgrading takes a lot of time and a lot of controlling afterwards. For me it is very interesting to read what have changed in the last actual upgrade. If there is small changes that no effect my way of using the profilux I probably can spare some time and upgrade my firmware after X different versions. I have looked a lot in the forum after changes in the latest firmware but have not find any information after 6.18 (latest now is 6.22).

Have I missed something?

Sincerely Lasse

[faltaren]

Any word on this?

[Matthias]

important note: the updates > 6.19 had major changes in the internal data structure, so it is very likely that the settings and PAB configuration will get lost
I recommend to update only if necessary


since our download are is in re-construction (again) I am not able to upload this without hassles, so until we have our new website with the new download center I'll post it here:

Version 6.22
- Bugfix: Scaling of dosing amount in timers corrected

Version 6.21
- DNS-resolution improved

Version 6.20
Hint: The settings must be restored after the update
- support for ExpansionBox2
- display of PAB-devices in ProfiLux menu improved (type, S/N)
- display of myGHL logo for connection state
- Bugfix: "myGHL active" is saved now
- several improvements for myGHL

Version 6.19
- myGHL for ProfiLux introduced

Version 6.18
- PAB configuraion via GCC improved

Version 6.17
- improved dynamic nominal value: sesonal nominal values can be defined with file

Version 6.16
- support for GHL Doser 2 Slave

Version 6.14
- Bugfix: Problem in V6.13 with assignment of Expansion Box over PAB solved

Version 6.13
- support for Powerbar 5.1

Version 6.12
- support for models 3.1T and 3.1TeX
- Bugfix: Lightdemo and time lapse
- simultaneous operation of EHEIM-controller, Mitras Lightbar and GCC possible

Version 6.11
- constant flow control with flow-sensor and 1-10V-interface possible
- more stream pump groups, night decrease for each group adjustable, easier pump assignment
- improved spanish translation and small design improvements in web interface
- Bugfix: 1-10V-interface during maintenance
- Bugfix: Thunderstorm with ProfiLux Touch
- function "Waterchange" with index > 1 for sockets and progr. logic available

Version 6.10
- support of new ProfiLux-Touch functions (with ProfiLux-Touch firmware 1.05 or higher): Labels customizable

Version 6.09
- minimal pH-hysteresis reduced to 0.05
- Info-Text during booting and for menu Info & Support customizable
- cloud simulation during low brightness optimized

Version 6.08
- improvements web interface (dosing overview, tablet and smartphone optimization, Level alarm reset)
- better support for dosing pump control
- 8 instead of 4 dynamic nominal value channels
- 8 instead of 4 variable illumination channels
- thunder-sound during thunderstorm (in combination with GHL Control Center 1.0.4.8)

Version 6.07
- webserver performance improved, thereby apps and webinterface are faster
- improvements web interface
- maintenance programs consider also the Mitras Lightbar now
- variable illumination for Mitras Lightbar usable, too
- "Lightdemo" and "Time lapse" for test and demonstration purposes can be enabled directly on the ProfiLux
- variable illumination can use illumination channels 1-16

Version 6.06
- new web interface design, improvements and extensions
- extensions for webserver, neccessary to use the new function of the apps (1.2 and above)
- new tokens

Version 6.05
- the same firmware for 4 languages: German, English, French, Spanish
- improvements web interface

Version 6.04
- email transmission via SSL

Version 6.03
- fix communication problem USB

Version 6.02
- support for Mitras Lightbar
- improvements web interface

Version 6.01
- problem with alarm LED solved

Version 6.00
- support for PLM-PWC
- time zone for web interface corrected

Version 5.17
- support for level cards in ExpansionBox with firmware V107 (affects ProfiLux 3 only)
- level inputs at level cards (in ProfiLux or ExpansionBox) are available for flow
- level control reworked (inverting / reaction time)
- new Tokens (Flow, Reminder) for creating own web pages in ProfiLux (affects ProfiLux 3 only)
- web interface extended, e.g. new overview page for sensors, webcam, illumination channels and switch plugs (affects ProfiLux 3 only)
- longer file path for webcam (affects ProfiLux 3 only)
- correction timeshift for illumination channels at ProfiLux2 models
- corrections when adding an extension cable for the temperature sensor

Version 5.16
- support for EHEIM-controller in app (affects ProfiLux 3 only)
- emails are sent also during smooth DST adjustment to the correct time (affects ProfiLux 3 only)
- in descriptions illegal characters are deleted which may result in problems with the app (affects ProfiLux 3 only)
- more virtual sensors possible (affects ProfiLux 3 only)
- support for new card PLM-pH/Redox-Cond
- performance optimized
- display of alarms and level-control improved

Version 5.15
- adjustments for ProfiLux 3 Outdoor
- support for new cards PLM-4Level and PLM-pH/Redox-2Level
- new tokens for creating own web pages in ProfiLux
- digital inputs can start now all special actions (e.g. like waterchange 2 or maintenance 3 etc.)
- ProfiLux is prepared for the new GHL-apps
- NTP: timezones extended
- for waterchange and auto top off with the same sensors it is possible now to use different sockets without the need to use the programmable logic
- minor bugs of the previous versions fixed
- prepared for the coming new firmware for ProfiLux Touch and SMS-module

Version 5.14
- support for the new ProfiLux models 3.1A ( eX) and ProfiLux 3 Outdoor
- support for flow sensors
- correction EHEIM display

Version 5.13
- support for the new ProfiLux models 3.1N (eX)
- level sensor control reworked, more flexible settings possible

Version 5.12
- webserver is locked after entering a wrong password 3 times
- 4 separate feedpauses (affects ProfiLux 3 only)
- support for LED-lamps from Eco-lamps
- wrong display of large operating hour stands fixed
- monitoring of PAB-devices extended (affects ProfiLux 3 only)
- configuration of PAB powerbars over ProfiLuxControl added (affects ProfiLux 3 only)
- again optimization of Aqua Illumination control
- current measumenent precision of PAB powerbars doubled (affects ProfiLux 3 only)

Version 5.11
- controlling (e.g. of temperature) with dynamic nominal values (affects ProfiLux 3 only)
- flash control for Aqua Illumination lamps optimized
- support for the new VorTech-Controller modes in firmware 1.03 (affects ProfiLux 3 only)
- PAB-communication optimized (affects ProfiLux 3 only)
- support for the new ProfiLux Touch functions in firmware 1.02 (affects ProfiLux 3 only)
- virtual sensors with source sensors which are located in an Expansion Box optimized (affects ProfiLux 3 only)

Version 5.10
- stronger signal filter for sensors, values will be more averaged
- temperature compensation for oxygen sensor reworked
- solved problem with description text which was not stored permanently (affects ProfiLux 3 with French and Spanish firmware only)

Version 5.09
- descriptions for sockets can be stored in ProfiLux, too (affects ProfiLux 3 only)
- new tokens for the use of descriptions in the web interface (affects ProfiLux 3 only)
- support for the new SMS-Module-PAB (affects ProfiLux 3 only)
- optimization of the communication during higher load (e.g. connection of ProfiLux View, SMS-Module-PAB and PC at the same time)

Version 5.08
- descriptions for sensors and illuminations can be stored in ProfiLux, too (affects ProfiLux 3 only)
- new tokens for the use of descriptions in the web interface (affects ProfiLux 3 only)
- support for the new ProfiLux Touch (affects ProfiLux 3 only)
- support for the new expansion card PLM-pH/Redox (measurement range pH/redox can be adjusted)

Version 5.07a
- inputs of level sensors can be inverted
- output of fast waves for wavebox optimized
- unlimited duration for maintenance possible

Version 5.07
- new operational mode for timers - cyclic switching is possible now, even by a random generator
- webserver optimized (affects ProfiLux 3 only)
- time shift function for illumination run and cloud simulation
- illumination runs can be copied from one channel to another (also time shifted)
- current pumps can be switched off completely during the night decrease
- firmware version of intelligent expansion cards is shown during booting
- built-in sensor inputs of the Expansion Box can be deactivated when they are not needed (with EXB-Firmware 1.05 and higher possible) (affects ProfiLux 3 only)
- inactive illumination channels output 0% brightness
- ProfiLux II Outdoor saves measurement range "salt water" at power cut
- communication over PAB optimized (affects ProfiLux 3 only)

Version 5.06
- 3 channel lamp from Aqua Illumination can be controlled
- optimization of settings for PLM-LAN and PLM-WLAN via ProfiLuxControl
- display of EHEIM state improved
- flashes also via integrated 1-10V-interfaces of the Expansion Box (with EXB-firmware 1.04 and higher)
- bug removed: EHEIM-Controller overwrote pH-calibration under certain circumstances

Version 5.05g
- controlling of older Aqua Illumination lamps optimized
- measuremnt of air temperature below 0°C possible
- wider range of nominal value for air temp.

Version 5.05f
- display brightness keeps maximal during calibration (affects ProfiLux 3 only)
- stronger and longer thunderstorms possible
- email notification through ProfiLux 3: tokens in the message are evaluated, it is possible to send emails with actual states (affects ProfiLux 3 only)
- current pumps can be assigned to pump groups in any order
- token $$SWIC$$ for displaying the current of a power outlet in a webpage (affects ProfiLux 3 only)
- supports EHEIM-Controller (control of EHEIM Professional 3e filter)
- automatic error reset in the level control
- ProfiLux 3 offers now 4 independent maintenance programs, all interfaces and sockets are included (affects ProfiLux 3 only)
- ProfiLuxControl is able to display the voltage of each 1-10V-interface
- ProfiLux reads the currents in a Powerbar-PAB, ProfiLuxControl is able to display them (affects ProfiLux 3 only)
- it is possible to use token $$OTVI$$ in loops (affects ProfiLux 3 only)

Version 5.04
- Firmware update for VorTech-Pumps possible (affects ProfiLux 3 only)
- new token $$OTVI$$ (display 1-10V-interface) for own web pages (affects ProfiLux 3 only)

Version 5.03c
- problem while numbering digital powerbars or dosing units solved (affects ProfiLux 3 only)
- support for VorTech-Controller (affects ProfiLux 3 only)
- display of PAB-components in ProfiLuxControl (affects ProfiLux 3 only)
- timers: correction of switching around 0:00 at certain days of week
- count of allowed files increased to 100 (affects ProfiLux 3 only)
- improvement of connection over LAN (optimization for VPN, MTU changed) (affects ProfiLux 3 only)
- problem solved: calibration of some cards in ProfiLux 2 was not possible

Version 5.02
- moon symbol on the display (affects ProfiLux 3 only)
- email notification (affects ProfiLux 3 only)
- time synchronization with SNTP (affects ProfiLux 3 only)
- new tokens for creating dynamical web pages (affects ProfiLux 3 only)
- support for PLM-DALI and PLM-2L4S in expansion box (affects ProfiLux 3 only)
- remote control over ProfiLuxControl for ProfiLux 3, too
- removed bug: settings night decrease and controller activity disappeared after reset
- up to 16 current pumps controllable (affects ProfiLux 3 only)
- night decrease for temperature now up to 5°C adjustable
- RSS-Feed (affects ProfiLux 3 only)

Version 5.01
- measurement recording for sensors in Expansion Box (affects ProfiLux 3 only)
- new tokens for generation for dynamic wep pages (affects ProfiLux 3 only)
- firmware update without confirmation on ProfiLux possible (works for updates after this update)
- tokens are replaced in XML and Javascript files now, too (affects ProfiLux 3 only)

Version 5.00p
- compatibility of the web interface to the common web browsers improved (affects ProfiLux 3 only)
- direct login for all file types possible, not only for HTML (e.g. needed for iPhone apps) (affects ProfiLux 3 only)
- digital powerbars / dosing units can be connected at S5-S8, too (with that it is possible to use outputs 25-48)
- changes in display level diagnosis
- TCP/IP automatic retransmit when having a bad connection (affects ProfiLux 3 only)

Version 5.00o
- PAB settings and measurement memory remain after power cut (affects ProfiLux 3 only)
- webserver login possible via browser address possible (affects ProfiLux 3 only)

Version 5.00n
- webserver with password protection (affects ProfiLux 3 only)
- sensor settings over webserver (affects ProfiLux 3 only)

Version 5.00m
- support for SMS unit

Version 5.00l
- behaviour of current pumps while inactivity selectable: Off or Minimum
- programmable logic: Function XOR added

Version 5.00k
- problem with detection of intelligent cards when ProfiLux View is connected fixed
- improvement of PC-connection speed and stability
- problem with auto. dosing when using timer above nr. 8 fixed

Version 5.00j
- display of level, moon phase and pump state possible
- level inputs of Expansion Box can be used (affects ProfiLux 3 only)

Version 5.00i
- reminder texts are shown more frequently
- files can be downloaded from the webserver with TFTP-GET (affects ProfiLux 3 only)
- webserver supports XML files (affects ProfiLux 3 only)
- better communication with intelligent cards (like PLM-DALI or PLM-4L)
- cloud simulation optimized

[Lasse]

Thank you Matthias

Sincerely Lasse

[pommie]

Any chance we can have this firmware information thread updated with the latest versions.
Ive checked the website and there is nothing listed for ver 6.23

thanks

[Vinny]

pommie, when you go to our downloads section click on the latest version of GCC. In that screen, click on "change log", you will see all the changes there.

[pommie]

Hi Vinny,

I looked at the download page and where it has description there is nothing listed?

https://www.aquariumcomputer.com/dow...irmware-v6-23/

Capture.JPG

[Vinny]

Hi,

All of the Profilux firmwares are now bundled with GHL Control Center. You will find the latest P3 firmware when you click on the newest version of GHL Control Center:
https://www.aquariumcomputer.com/dow...nter-v1-0-8-3/