Results 1 to 8 of 8

Thread: where to connect the STDL L4-4

  1. #1
    Join Date
    31.10.2009
    Location
    Tobyhanna
    Posts
    63

    Default where to connect the STDL L4-4

    I Have a Profilux 3 firmware 6.12
    i have the powerbar 6D connected to Port S1-S4

    Do I connect the STDL L4-4 to Port S5-S8 ?????


    and what other steps do i need to do to make it work ??


    Thank you Once againnnn..
    Last edited by janey; 02.09.2015 at 19:12.

  2. #2
    Join Date
    13.11.2013
    Posts
    1,001

    Default

    Hello,
    yes you connect it to Port S5-S8.
    The STDL will react to the sockets S5-S8 and there is nothing else to do.
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  3. #3
    Join Date
    31.10.2009
    Location
    Tobyhanna
    Posts
    63

    Default

    Thank you so much...
    Love you guys and your products..
    This is my 3rd Profilux controller unit
    ..

  4. #4
    Join Date
    31.10.2009
    Location
    Tobyhanna
    Posts
    63

    Default

    OHH Noooooo wait ... On Socket Function Do i check the
    Digitalbar connected to S5-S8 ???

    Ohh I'm sorry.. I just forgot how to do this again ??/

  5. #5
    Join Date
    06.02.2012
    Posts
    2,020

    Default

    Do i check the Digitalbar connected to S5-S8 ???
    If you have a STDL L4-4 the box must stay unchecked - it´s not a digital bar.

  6. #6
    Join Date
    31.10.2009
    Location
    Tobyhanna
    Posts
    63

    Default

    OK, ...

    Question again..
    I have the Powerbar 6D (not PAB) connected to S1-S5 and clicked digital bar box ... i connected the STDL L4-4 to S5-S8..
    I see that on the STDL L4-4 1st light S1 is ON.. But i dont see it on the GHL control Center / socket function as being on..



  7. #7
    Join Date
    13.11.2013
    Posts
    1,001

    Default

    Hello,

    this is correct because the STDL4 reacts to Socket S5-S8 and in your settings you set the socket S5 to "Always on".
    If you connect the STDL4 to S5-S8 the S1 Socket of the STDL4 reacts to the S5 socket in GHL Control Center and so on.

    If you didn't programm your PowerBar 6D the Powerbar reacts to socket S1-S6 in GHL Control Center and it has an overlap with the STDL4.
    You must programm the PowerBar 6D to react to S9-S14 and reasign the function to this sockets.

    powerbar.jpg
    No support or warranty issues over PM! Please send PMs to the moderators only if you have general problems with using the forum! Thanks for helping us to keep the support efficient.
    Kein Support oder Reklamationsabwicklung über PM! Bitte senden Sie an die Moderatoren nur PMs bei allgemeinen Problemen mit der Verwendung des Forums! Danke dass Sie uns dabei helfen, den Support effektiv zu gestalten.

  8. #8
    Join Date
    31.10.2009
    Location
    Tobyhanna
    Posts
    63

    Default

    YESSSSSSSSSSS

    Thank you got it working..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •