Hi everyone,
Due to the fact that the plastic glass protection on my Mitras LX6 was completly burnt, I have replaced them with a normal glass (a 2mm traditional glass).
Can you tell me whether it...
Type: Posts; User: courlet
Hi everyone,
Due to the fact that the plastic glass protection on my Mitras LX6 was completly burnt, I have replaced them with a normal glass (a 2mm traditional glass).
Can you tell me whether it...
Thanks, following these instructions, it works (the one through USB)
Hi, as every 6 months, I have to performe the wifi update on my P4. And as each time, it is the same nightmare.
I went again through the instructions, but all the options that appears easy to...
Hello,
I have just update the wi-fi firmware in my P4 as connection to myGHL apps was not more possible (hopefully I was not in holidays far from my tank when it occured).
Update is successfull...
Hello, I am currently successfully monitoring 4 tunze pumps thanks to the P4.
Is it possible to add 2 vortech pumps and to monitor them simultaneously with the tunze ?
I mean in the same stream...
Hey, I have 10 LX6200 lights for few years (around 4 years for some of them) that I have updated to LX6300 at launch of the LX7 series.
The plexi cover of my lights was a bit burned in front of the...
But how would you get the control over the Jebao pumps? I have RW20 pumps with each a controller but without any option to transfer the lead to a separate controller.
Great news!
Can you tell me when?
Why limiting to 24? I would recommend 48, which is one dosing any single half hour.
Thanks
Hello, using the dosing schedule in the GHL controller, we can’t have more than 8 slots per day (per dosing pump).
Why such limitation?
Is there any option to have more?
Thanks
Thanks
Hi all,
Just a question to optimize the calibration: I use fluid PH 7 and 9 => with which one I should start the calibration? The lower (the 7) or the higher (9).
Maybe no impact, but just wanted...
Hi, I have bought the KH Director and I use it successfully.
I looked at ION Director, however the more critical matter to follow is the phosphate and unfortunately this is not measured. I would...
Hello,
I have a very surprising problem with my KH Director.
When asking for a measurement, nothing happen except that I get a noise from the pump. The pump doesn't run but only issue a noise....
Hello, I have just bought the STDL4-4 powerbar to add on my system.
The powerbar is supposed to be connected to my Expansion box 2. First question: is it possible to connect the STDL4-4 to the...
Hi, I would appreciate some help in order to reach the following configuration:
I have 2 level sensors in my fresh water tank:
- first one is on the top of the tank (tank is full)
- second one...
OK many thanks!
I guess it is the same answer considering the distance between the Profilux and the Extension box?
Thanks
By saying "the transmission rate decreases", does it mean that the quality of the signal will decrease so that it may not work properly?
Hello, I have a profilux 4 and would like to have a PAB in my cellar (where I will have the fresh water tank) in order to monitor the levels of water.
Problem is that the PAB will be around 50...
Sorry, it works now ! I did not change anything, except that I tried to open the file you mentionned, prior to launch the update process. Curious, but now it is fine.
Thanks
It is the case, the file is already in the directory. But it still doesn't work.
Help please !
what is the bin directory?
Is there a relation with the bin where the files cancelled are stored?
I am a Mac user, using a PC only for GHL purpose and do not have any knowledge on IT.
Thanks a lot
No, there is nothing in the bin
Unfortunately, it doesn't change anything. I have desactivated everything and it is still the same message!!!
Thanks, it works now !
Still doesn't work, even after disconecting the P4.
Attached is the screen shot showing the updating tool and the error message. 11123
Below is the full message that I get by clicking on "détails"...