Search:

Type: Posts; User: Vinny

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    56

    Hi, If you get a ProfiLux 3 and install a...

    Hi,

    If you get a ProfiLux 3 and install a PLM-PWC card, you will be able to control the LX6 through the ProfiLux. As long as the ProfiLux is connected to the internet, you will also have mobile...
  2. Excellent!

    Excellent!
  3. Replies
    3
    Views
    2,912

    Ideally, you should create the ON/OFF schedule...

    Ideally, you should create the ON/OFF schedule using an Illumination channel instead of a timer function since this is a light you're controlling afterall.

    If the Kessil control cable is designed...
  4. Hi, The order in which you connect the PAB...

    Hi,

    The order in which you connect the PAB devices (KHD, SA Doser (converted to Slave mode), etc.) does not matter. What is most important is that you do not create a loop. For example, you can...
  5. Replies
    6
    Views
    321

    The trend depends on your specific tank and KH...

    The trend depends on your specific tank and KH consumption patterns. Typically consumption increases just before the lights turn ON, but this is not always the case as every tank will have a...
  6. Any dosing pump which was connected to and...

    Any dosing pump which was connected to and controllered by the SA doser should also have its settings written down and copied over to the P4e.
    Yes, you can calibrate the KHD probe after connecting...
  7. Before you connect your Doser and KHD to the P4e,...

    Before you connect your Doser and KHD to the P4e, go into your SA Doser and copy the pump flow rates for each head that is used by the KHD. Write down your KHD settings too. This info will have to be...
  8. Replies
    15
    Views
    1,352

    ProfiLux 4e is included in the push notification...

    ProfiLux 4e is included in the push notification feature.
  9. Replies
    1
    Views
    111

    At 1 year old, it may be time for a new probe.

    At 1 year old, it may be time for a new probe.
  10. Thread: Waste Water?

    by Vinny
    Replies
    1
    Views
    69

    The KHD will not test if the waste container fill...

    The KHD will not test if the waste container fill level is above the maximum value you set.
  11. Replies
    1
    Views
    171

    Hi Fred, You can achieve this by powering a...

    Hi Fred,

    You can achieve this by powering a solenoid via a Powerbar socket. Since you will need 2 solenoid values, you will need 2 Powerbar sockets for this task. One socket will have the AWC...
  12. Memorial Day sale is still going strong. Get...

    Memorial Day sale is still going strong.
    Get your LX7 while supplies last!
  13. Replies
    3
    Views
    148

    Please open a support ticket if you have not done...

    Please open a support ticket if you have not done so already.
  14. Replies
    2
    Views
    285

    Hello, Depending on the specifics of the...

    Hello,

    Depending on the specifics of the problem, you may find a solution in the ProfiLux troubleshooting article. I recommend starting here and if the problem persists, you can open up a support...
  15. Replies
    1
    Views
    175

    Yes that is OK.

    Yes that is OK.
  16. GHL Memorial Day Sale - 15% off Mitras LX7 fixtures!

    13203

    GHL USA is kicking off the upcoming Memorial Day weekend with a special sale!
    From now until Tuesday, June 7, all Mitras LX7 are 15% off!
    This is your chance to purchase one of the most...
  17. Replies
    5
    Views
    241

    Check valves are unnecessary.

    Check valves are unnecessary.
  18. If you are viewing the ProfiLux 4 firmware folder...

    If you are viewing the ProfiLux 4 firmware folder in the GCC v1137 directory, you will see the most recent firmware which is V7.28
  19. Replies
    5
    Views
    241

    The tube connections look OK. Do you know the...

    The tube connections look OK.

    Do you know the age of the dosing pump?
    Do you know when the original owner replaced the tubes or if it was done at all?

    You can manually run a dose for 40 - 50ml...
  20. Replies
    6
    Views
    321

    Okay good, you can keep the 12% adjustment as-is....

    Okay good, you can keep the 12% adjustment as-is. The purpose of this tool is to eliminate any discrepancies in the water sample tube volume and pump head calibration. As long as the results are...
  21. Replies
    6
    Views
    321

    Hello, What values do the KHD show when...

    Hello,

    What values do the KHD show when testing with the 7.5 fluid after the adjustment is made?
  22. Replies
    2
    Views
    396

    Hello, If you are still having trouble with...

    Hello,

    If you are still having trouble with this, please open a support ticket for direct assistance.
    https://www.aquariumcomputer.com/support/tickets-enquiries/
  23. Replies
    2
    Views
    182

    Hello, Yes you can recover your doser. :) ...

    Hello,

    Yes you can recover your doser. :)

    Since this is a slave D2.1, you will have to connect to your primary device and follow the "Emergency PAB-device update" steps as shown here:...
  24. Replies
    3
    Views
    215

    If you are still seeing this, please open a...

    If you are still seeing this, please open a support ticket for further assistance.
  25. Replies
    1
    Views
    175

    Use a positive value when you want to increase...

    Use a positive value when you want to increase the IOND value, negative value to decrease. In your case, use (11).
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4