Perfect, thanks for the help!
Type: Posts; User: StarF
Perfect, thanks for the help!
Hi
Thanks, must be the summerheat getting to me :)
You dont think 2 bars over so small a area would make the corals to each side of them look "odd" ? as they will get diffrent spectrum on each...
I am about to set up a small frag tank, for sps corals. The corals are gonna be under 20cm of water (more or less), and the measure ments is 45x32cm, how many lightbars would be needed to grow sps...
i am about to invest in Mitras-LX and would need this function aswell..
I have 4 Mitras units, 2 of them have gotten dark spots in the splash screen, all units are running the same power and light schedule (high output 70%), and the reflectors does not have any miss...
i would love to get an anser for this. As i am setting up a frag tank, that i plan to lightup with lightbars if i could get them in the same layout as the 7206
Has anyone tried to run Mitras 6300 or 7100 with the deep antic lightbars? how is the result, does it add anything? i can see it has a few more blue leds in diffrent ranges.
I still have this isue that i wrote about in to top, When GHL connect to LX
When i go into Light composer, chose output directly on lamp, and then adjust the light. If i then disable output on lamp, and then enable it again it dosent take effect.
it seems the problems...
Thanks, so this would be a correct setting? I am using the Vortech Controller options to run it.
10167
10168
10169
One fast question, i cant seem to find anything in the manual about this.
Pump channel, if i want 2 pumps to run in sync, so the 2 vortech pumps always do the same mode/speed should both be set to...
I havent tried to calibrate it yet, but it should change it value when i connect the prope no matter what. The sensor should be active. I just wanted to be sure before i tried something else, that i...
I have a Profilux 3 with this card in.
What ports are the Ph and Con? I take it the port on the bottom when the card is inseted into the profilux is the ph port, the one where the connection stick...
Yes the yellow is lagoon mode, my question was why is one driver red, the other purple when they both are running ntm mode? the purple is the color for ntm, i dont know what the red color is. When...
from what i recall the new mp40qd does not need to be upgraded to work. i just hooked mine up, and i dident do the upgrade pump part.
I have hooked up my 2 vortech mp40qd pumps to my ghl 3 unit with the vortech module. When i am running nutrienc export, and tidal swell, one of the pumps are purple and the other one is red, why is...
i upgraded my 6200 to 6300.. well worth it imo.. much better looking light...
i can confirm i have the same isue...
Replacement LED-Boards for Mitras LX 6300 fixtures; Includes 2 LED cluster boards.
***For upgrading existing LX 6 series fixtures to the same LED configuration offered in the Mitras LX 7206 LEDS
...
I just love how the new leds look, really a good update to my mitras 6200, well worth it!....
Thanks for providing this upgrade.
Good to know, dident know the lamps were updated along the way. I have 2 Mitras that is about 3 years old, mabye a bit older, and 2 pretty new units, so i guess a exchange of clusters would make them...
about to make my order to upgrade 4 lamps :) one question, these are never leds right? so they should put out more PAR ? (in theory) ?
Good point about the screw, just in time, i have to put these up tomorow :)
that much is clear to me..
I would expect at least there were a simple assembly instructions included. But i guess it dosent matter how the screw is incerted into the vertical bar.
could any one point me in the right direction?
How should the screw be placed in the horizontally alubar?
8752
like this
8753