Suchen:

Art: Beiträge; Benutzer: Vinny

Seite 1 von 20 1 2 3 4

Suchen: Die Suche dauerte 0,02 Sekunden; generiert vor 34 Minute(n).

  1. Antworten
    2
    Hits
    164

    Check your "Energy options" settings page and...

    Check your "Energy options" settings page and make sure all fixtures are set to the same settings.
  2. Antworten
    10
    Hits
    489

    myGHL is not working because you have not entered...

    myGHL is not working because you have not entered a DNS into the fields. Enter 8.8.8.8, save settings, disconnect, then wait 2 minutes before trying to add the device to your cloud account.
  3. Antworten
    10
    Hits
    489

    You can see which sensor is assigned to which...

    You can see which sensor is assigned to which level input by going to the Sensor state tab in the Level settings page. Toggle each sensor and look at the state. Whichever shows the (X) appearing and...
  4. Antworten
    10
    Hits
    489

    You cannot be connected through GCC and use the...

    You cannot be connected through GCC and use the update tool at the same time. That is why you were not able to connect via GCC.

    Power cycle the P4 and use the update tool again. First blank chip,...
  5. Antworten
    1
    Hits
    203

    Hi there, The Mitras Lightbar 2 (Model 60...

    Hi there,

    The Mitras Lightbar 2 (Model 60 Daylight) would be the ideal choice for that aquarium length. The model 60 is recommended for tank lengths between 59 - 70 cm so this size would work for...
  6. The sound of the alarm can be adjusted in the...

    The sound of the alarm can be adjusted in the General settings page. There you will also find the option to make it audible only during certain times of the day, if need be.

    Information on...
  7. Antworten
    10
    Hits
    489

    Hello, Based on the info provided and the...

    Hello,

    Based on the info provided and the testing you've done so far, the cause of the AWC behavior is due to the sensor(s) needing replacement.

    If your WiFi connectivity issue continues and no...
  8. Antworten
    1
    Hits
    402

    Hi, Both 2.0 and 2.1 are suitable for AWC to...

    Hi,

    Both 2.0 and 2.1 are suitable for AWC to an extent and the KHD.

    The difference is in the pump head design. Features remain the same.
  9. Antworten
    1
    Hits
    142

    Hi, That's not how the KHD is intended to...

    Hi,

    That's not how the KHD is intended to work...

    After each test result, the KHD automatically evaluates the necessary change based on how you set your control settings. It then makes these...
  10. Thema: Battery backup?

    von Vinny
    Antworten
    1
    Hits
    279

    Hello, The Tunze safety connector would run...

    Hello,

    The Tunze safety connector would run independently from the ProfiLux. The Powercut adapter also works differently than the Tunze adapter. More information about this feature can be found...
  11. Hi there, You would not be able to upload D2.1...

    Hi there,

    You would not be able to upload D2.1 SA settings onto the ProfiLux because these are two different products with very different hardware.

    You can however mimic the settings from the...
  12. Antworten
    1
    Hits
    392

    Hello, These are two separate issues: If...

    Hello,

    These are two separate issues:

    If you were able to connect through your network before and now you can longer do that, it may be for the following reasons:
    Weak signal strength, new...
  13. Please open a support ticket so we can look into...

    Please open a support ticket so we can look into this for you.
  14. Antworten
    3
    Hits
    258

    As mentioned earlier, the discrepancy is due to...

    As mentioned earlier, the discrepancy is due to the drain portion of the test. The KHD will run the drain pump slightly longer to ensure the measurement cell is emptied. As a result there will be air...
  15. Antworten
    5
    Hits
    658

    You can add 3 or more functions to a single...

    You can add 3 or more functions to a single Powerbar socket when you use Programmable Logic. The article here provides an example on how to do this:...
  16. Antworten
    2
    Hits
    238

    T8

    T8
  17. Antworten
    3
    Hits
    258

    Check the flow rate settings for this pump and...

    Check the flow rate settings for this pump and make sure you have the correct ml/min amount entered. The amount displayed in the fill container is based on the waste water plus some extra (incl. air)...
  18. Antworten
    1
    Hits
    202

    Open a support ticket for further assistance.

    Open a support ticket for further assistance.
  19. Antworten
    5
    Hits
    658

    https://www.aquariumcomputer.com/knowledge-base/ho...

    https://www.aquariumcomputer.com/knowledge-base/how-to-setup-a-standard-timer-on-off-function/
  20. If you download and use v1131 on your Win7...

    If you download and use v1131 on your Win7 computer, you will see there is no issue with this version. No issues on Win10 were reported either.

    Instead of using the auto-search option, enter the...
  21. Either the Wifi information entered is wrong or...

    Either the Wifi information entered is wrong or the IP being assigned is being used by another device on the network.
    If you set the doser to Obtain IP automatically, it will allow your network to...
  22. Did you search for and follow the steps in the...

    Did you search for and follow the steps in the how-to video?
    Start there.

    https://youtu.be/5D7KxXiLuO0

    If that does not work, open a ticket and provide specific details on your network and...
  23. USB connection requires GHL Control Center which...

    USB connection requires GHL Control Center which is a windows program.

    Connect via USB using GCC and you will be able to adjust your network settings.
  24. Antworten
    5
    Hits
    320

    Using the reference solution will rule out any...

    Using the reference solution will rule out any factors introduced by the API and Hanna kits.

    If you want to adjust the readings, go to the KHD settings page and at the top of the page you will see...
  25. Antworten
    5
    Hits
    320

    Hi there, Since the KHD is providing...

    Hi there,

    Since the KHD is providing consistent values and you've already checked the pH probe, that means everything on the unit itself is working properly which is great! Having also checked and...
Zeige Ergebnis 1 bis 25 von 500
Seite 1 von 20 1 2 3 4