Search:

Type: Posts; User: Shredded

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    3,247

    Today I finally made progress using the original...

    Today I finally made progress using the original serial numbers and the keys provided by Vinny. I initially tried to reset the SN on the Doser 2.1. It would not work and I could no longer assign it...
  2. Replies
    4
    Views
    3,247

    I wanted to post the resolution on this as I know...

    I wanted to post the resolution on this as I know once something moves to opening a ticket some of these never get resolved on here which doesn't help anyone.
    Germany was unable to replicate this...
  3. Replies
    4
    Views
    2,790

    I do, and it's embarrassing as I think I did this...

    I do, and it's embarrassing as I think I did this once before. Maybe though a change may be in order just because it was so easy to do. I frequently use my Iphone to use the GHL Connect app to dose a...
  4. Replies
    4
    Views
    3,247

    Hi MatthiasF, I have already confirmed the same...

    Hi MatthiasF,
    I have already confirmed the same is seen in GCC. There is no difference. I will open a support ticket as literally have put 30 hours into it the past two days just trying to resolve...
  5. Replies
    4
    Views
    3,247

    Firmware Update 7.2.4 Issues

    This weekend I switched over to the DSR system. While doing this, I took the opportunity to clean and calibrate all of my dosing heads. I turned all of them down to 0 for improved accuracy and less...
  6. Replies
    4
    Views
    2,790

    Resolved

    Resolved
  7. Replies
    4
    Views
    2,790

    Doser 2.1 head will not stop running

    Help! Was cleaning and recalibrating all of the dosing heads. when I went to calibrate head 3, the head never quit. It ran for an hour before I pulled the plug on my system. when i connect all the...
  8. Replies
    5
    Views
    2,873

    So recalibrate? Obviously you know this from your...

    So recalibrate? Obviously you know this from your experience, but what exactly is the alarm/error based on? As a user, I am looking at water parameters that would be out of wack... i.e. Oxygen level...
  9. Replies
    5
    Views
    2,873

    If I disable the sensor, the error goes away. I...

    If I disable the sensor, the error goes away. I can save the entry, reboot the app and when I enable the sensor the error returns. See attached screen shots below for settings.
  10. Replies
    5
    Views
    2,873

    Oxygen Saturation

    My O2 saturation is always between 103 and 104 %. I have lots of surface agitation, plus my skimmer so I am always supersaturated. My problem is no matter what I have my settings set to, it always...
  11. Replies
    12
    Views
    11,826

    Not sure if I can reopen this thread or not. I...

    Not sure if I can reopen this thread or not. I actually did not see this last post previously but I share the same concern that that has the heads wear, tolerances will change and at the very least...
  12. Replies
    12
    Views
    30,583

    Also on a minor note, Salinity (Manual) shows...

    Also on a minor note, Salinity (Manual) shows it's units in °C. I'm guessing not a lot of people are running Oxygen Sensors.
  13. Replies
    12
    Views
    30,583

    @doggydoc10, On the O2 sensor page, down at the...

    @doggydoc10, On the O2 sensor page, down at the bottom, if you turn on Dynamic Nominal Value, does the "Current Value" to the far right have a reading? My channel reads 8, but the "Current Value"...
  14. Replies
    12
    Views
    30,583

    I believe web interface. Version is 3.2.2. I...

    I believe web interface.
    Version is 3.2.2.
    I have not tried this on other platforms yet.

    The error message is for the Oxygen Sensor but it does not tell me what it sees as the value in error....
  15. Replies
    12
    Views
    30,583

    Incorrect Chart for Oxygen Saturation

    I have been dealing with an error thrown by my P4 on the O2 Saturation. See attached. My O2 saturation runs daily between 102% and 104%. Very consistent depending on the time of day but I constantly...
  16. Replies
    0
    Views
    6,706

    Water Replenishment

    I'm not sure if this is the correct support forum or not.
    I run my 8 tests per day on my KH Director at 100 ml samples. Over time this causes a a shift in salinity due to the auto top off. Is there...
  17. Replies
    12
    Views
    11,826

    I was actually going to start my own thread but...

    I was actually going to start my own thread but mine is so close to this I hope the OP does not mind me joining in. Please have this deleted if necessary. Here is mine, specifically...
    I have fought...
  18. Replies
    1
    Views
    2,828

    Switched outlets confused

    So I did some cable management this weekend since I have switched over to LED from metal halide and removed the metal halide ballasts. This gave me more room and I rearranged 2 of my powerbar 5.1s....
  19. Thread: KH Readings

    by Shredded
    Replies
    7
    Views
    7,303

    So, I received 2 new bottles of reagent and the...

    So, I received 2 new bottles of reagent and the replacement PVC tubing from Marco. I changed out the PVC tubing with no affect. As for the bottle of reagent, it is close to empty so I'll just run it...
  20. Thread: KH Readings

    by Shredded
    Replies
    7
    Views
    7,303

    I believe the reagent in the "new bottle" is...

    I believe the reagent in the "new bottle" is light blue. My first bottle was the 500 ml bottle that came with the Ultimate kit. It was perfect. No air what so ever. When it arrived with the kit, it...
  21. Thread: KH Readings

    by Shredded
    Replies
    7
    Views
    7,303

    Thanks Thilo, Yes, I have emptied and flushed...

    Thanks Thilo,
    Yes, I have emptied and flushed the measurement cell so many times that I actually affected the salinity on a 300 gallon tank because of the top off system. My calibration is exact...
  22. Thread: KH Readings

    by Shredded
    Replies
    7
    Views
    7,303

    KH Readings

    I have had my KH Director up and running for a couple of months. It took a week or so but we finally got it dialed in. Every reading matched my Hanna exactly, every time. At that point I turned on...
Results 1 to 22 of 26
Page 1 of 2 1 2