Search:

I want to use a Kalkwasser container to help me control low PH.
I have a dosing pump with the profilux 3 ex.
The contaner does not have or need a level switch so how would i set this up?

Hello Matthias

Just wanted to let you know with 5.1.1 I was experiencing lost connection issues. I have a P3EX with firmware 5.06
I reverted back to 5.1 and have no more problems
It would lose...

So do you have to use a seperate 10v PSU for every driver?
If I have 36 LED's and 3 Drivers would I also have to run 3 10 Volt PSU's?

I am having the same problem with 5.02g. My webserver is not responsive and I can no longer connect to it. I reset the profilux and it starts working again but only for about an hour. This never...

I cant seem to figure out how to select the probes when setting up emailing through the profilux. It doesnt allow me to select variable text like it does when emailing through PC.
I am using the...

Anyone in the US have the tools to do this? Is it possible that the probe is also defective or more likely just the Connector?
I hate to spend another $230 on a Probe that last a year.

I dont have the tools for crimping them.

I can no longer calibrate my conductivity probe. I believe there is something wrong with either the probe or the profilux 3. The ADC values are both 18 and the reading is always 99.9 mS. It started...

I had a few questions regarding the GHL dosing pumps. I wanted to buy a 4 dose unit the first pump to dose MB7 and second for Carbon source. The 3rd and 4th I was thinking about using to do a 2...

I wanted to know if it was possible to base my skimmer operation based on the water level in the sump. Basically I want the skimmer to turn off if the water level in the sump gets too high so it wont...

After entering a static IP for the Profilux I have not had the issue where I had to reset the P3 on a daily basis. I belive it had to do with my router switching its IP.

I am trying an experiment........
I had my Profilux 3 set to obtain address automatically and it seems to not connect after the DHCP assigns it a new IP which I have set to happen every 24 hours. ...

Well we are having almost the same issue, but we are not using the same router or wireless bridge. I am using the TRENDnet Wireless N Gaming Adapter TEW-647GA and a Dlink DLG 4300 router. The odd...

Ok I got it to reconnect over the wireless network after resetting the Profilux. This would indicate to me its a firmware problem or hardware issue with my unit and not software. I guess it could...

My signal strength is over 90% to the bridge. I'm not able to connect to the profilux over the lan at all right now it just stopped working today for some reason. I will try and reset the profilux to...

It seems to happen in all menus. Its like it freezes for a second then says communication lost but does not give any error codes. I had it happen the most while looking at sockets and illumination...

OK I got it, I had to use the flash utility to update the firmware before it would work. I could not communicate via USB or the R232 with the Software so I used the flash utility with the R232 and...

I did read somewhere that the software and the firmware have to match, but I have a firmware version 5.0 and I cant find that software. Any ideas? or will this even work?

I recently updated my Profilux 2 ex to a 3 and was trying to connect with the USB. I get communication error 41 when trying to connect. I have Windows 7 64 bit and the Profilux usb driver installed....

Did you ever get it working cerreta?
I have the same adaptor but have not yet installed the P3 upgrade kit due to all the problems people are having. Want to wait until its ready for release.

Very interesting statement since 99% of all "game controller bridges" are USB which would have been a lower cost solution. I'm very disappointed in this news since I also was duped into buying the...

Hello Mathis

Im am having problems with my Conductivity settings. I have the GHL probe and my calibration seems to go from good to bad or 54.0 to 0 in a couple weeks. I have tried re calibrating...