aha, yes it switches off before 100%....looks to turn off at about 90%
I have 4 aquaray's controlled via an EVG-AP-2F in order to link the rays in banks of 2...
This I know is a very non standard...
Type: Posts; User: evilscoop
aha, yes it switches off before 100%....looks to turn off at about 90%
I have 4 aquaray's controlled via an EVG-AP-2F in order to link the rays in banks of 2...
This I know is a very non standard...
aha, might be nice for you to update the change log then please :D
yes im still on 503a, changelog only goes to 503b and nothing in that is worth the update atm......
actually 27-9-10 was the last firmware I will go to, as you have failed to update the change log at http://www.aquariumcomputer.com/System/Support/dnd_normal/Firmwarehistory_ENG.txt since 5.0.3b and...
Hi
I have 4 aquarays controled via ghl
These are set for cloud simulation, with max dimming set to 85%.
I also have these set to fade off from 6:30 pm till 8:30 pm
All is fine untill fade...
Guess this is why we havnt had a firmware update in a while.......
feature difference would be very annoying, considering how much we pay for hardware...id expect the control software to be free as part of the cost of ownership must be the software/firmware dev.......
hang on, does this mean your intending to charge people for the "pro" version ????
Nominal value for pH says - 0.08ph when its set in the probe control to 8.0
Does the same for the virtual probe copy...
Not sure were to put bug reports, so might as well dump it here :D
P3...
doh...
I thought it said in the manual that it took care of that...
Thanks for that
Ok now that you can connect to the p3 via network, usb and rs232, any chance of a linux built client ???.....or evan one that will actually function under wine, you cant click save or load under...
I seem to just get a blank page...
I have this in my user.html file :-
<p>Firmware - $$FWVS$$ $$FWDA$$</p>
<p>orp $$SWIS[05]$$</p>
user.html was created in vim on linux, if that makes...
For completness, im posting the resolution.....
Ive used a virtual probe....made a copy of ph1
set values the same, cept two position controller
set non kalk top up to :-
water 1
and
ph-2...
Ok my current setup isnt working for this, and after 2 days thought id see if I could get some advice
Ive setup 2 sockets on the power with the following logic :-
Water 1
and
PH increase
...
Help please....
I may have the wrong end of the stick here....
Ive set my halides on illumination 2, on at 11am off at 5pm
Ive ticked the box for rainy day
Halides are set non dimmable
Ive...
Doh RTFM
never was good at that
thx
Ok am I doing something wrong
I can only get the control to work on an unsplit L line
if I connect it via a splitter it no longer works
surely the propcontrol doesn't need 2 L lines
or am I...
I'd hope that when p3 comes out, with it's Ethernet and webserver, that it whould be able to update from ntp pool
ahhh thank you
ok i give...
ive hunted the manual and the forum...
what is the dcf port used for ????
Wow expensive rear board
I appreciate the reply.
ok ill keep it simple :D
im aware of whats in the upgrade package
but surly the front board with cpu and display on it is the most expensive single component in the box...:eek:
You cant...
so you mean those that upgrade to a p3 from p2 wont have the new cpu or the new flash ????????
I thought most of the brains of the box were on the lcd pcb....
what more is there in the box but...
I have a pre-order for the p3 upgrade
Correct me if im wrong, but after upgrade, ill have a useless cpu board + some other bits...
It'd be nice if you could buy a housing + bits to perhaps make...