Suchen:

Art: Beiträge; Benutzer: frank40

Seite 1 von 2 1 2

Suchen: Die Suche dauerte 0,00 Sekunden.

  1. Antworten
    2
    Hits
    1.622

    i didn't see the new FW on the downloads link, is...

    i didn't see the new FW on the downloads link, is it up already?
  2. Antworten
    2
    Hits
    1.294

    I would just get a cheap laptop to use for the...

    I would just get a cheap laptop to use for the Profilux because from what i understand it is a lot more expensive to write the software for Mac vs windows and some company's are not willing to go...
  3. Antworten
    2
    Hits
    1.426

    Thank you BoBoxx, it was the 2-position...

    Thank you BoBoxx, it was the 2-position controller setting. i wonder what else we need to look out for
  4. Antworten
    2
    Hits
    1.426

    Co2 not switching off

    I have a P3 that has running flawlessly until now. I have 2 ph probes, 1 is for tank readings and the other is for Cal Reactor control. i have my nominal value setup as 6.3 for the Cal reactor but...
  5. Antworten
    63
    Hits
    41.643

    i am jumping on the LED bandwagon and building a...

    i am jumping on the LED bandwagon and building a small for my fuge/frag part of my sump. i am using 12 Cree x series leds with a meanwell driver hooked up to a EVG board.

    My question is when you...
  6. Thema: Redox card

    von frank40
    Antworten
    2
    Hits
    1.449

    i figured that but the distributor said it...

    i figured that but the distributor said it doesn't have to......so i guess i have to get calibration fluid
  7. Thema: Redox card

    von frank40
    Antworten
    2
    Hits
    1.449

    Redox card

    I just added a redox card to my P3, now i was told that the probe doesn't need calibration because it is usually factory calibrated but i am getting a reading -89 on the P3 so i am assuming that it...
  8. Antworten
    2
    Hits
    1.313

    i had the same problem then it was my...

    i had the same problem then it was my carelessness of not typing "Admin" in the name field. the password is whatever you choose under system-webserver.
  9. Antworten
    20
    Hits
    6.563

    thx......always the simple things elude us

    thx......always the simple things elude us
  10. Antworten
    23
    Hits
    5.063

    sometimes the answer is right in front of...

    sometimes the answer is right in front of you.....thx. i had typed admin instead of Admin, all good now
  11. Antworten
    23
    Hits
    5.063

    i am using Firefox and i have checked the casing...

    i am using Firefox and i have checked the casing in the password, still not logging in
  12. Antworten
    20
    Hits
    6.563

    i had no trouble doing the upgrade. i did the...

    i had no trouble doing the upgrade. i did the firmware upgrade first then installed the new software version.

    i just cannot log into the webserver anymore, i get the message "ACCESS DENIED". i...
  13. Antworten
    23
    Hits
    5.063

    nothing like yours....just "Access Denied"

    nothing like yours....just "Access Denied"
  14. Antworten
    23
    Hits
    5.063

    i have the same issue after the firmware upgrade,...

    i have the same issue after the firmware upgrade, i can't log into the webserver. i tried changing the password several times but no access.
  15. Antworten
    7
    Hits
    1.849

    before going out to buy another piece of...

    before going out to buy another piece of equipment, i decided to reset the security on the router to WPA2 instead of WEP and reset the Linksys 610 bridge. i went through the install process for the...
  16. Antworten
    7
    Hits
    1.849

    ok, no luck on bridging an Apple extreme router....

    ok, no luck on bridging an Apple extreme router. the only solution i have left is to purchase an airport express and hardwire it to my existing router and create a new wireless network so that the...
  17. Antworten
    7
    Hits
    1.849

    Lynksys WET610, I am going to try to bridge my...

    Lynksys WET610, I am going to try to bridge my Apple airport
  18. Antworten
    7
    Hits
    1.849

    after further investigating, i found that my...

    after further investigating, i found that my wireless bridge is the culprit. I connected the P3 directly to my router and it worked fine but then i hook up the bridge, it losses the connection...
  19. Antworten
    7
    Hits
    1.849

    I rebooted the P3 and now it is not even listed...

    I rebooted the P3 and now it is not even listed on my router. I am going to try connecting it directly to my router over the weekend.
    I am using a Lynksys WET610N bridge and Verizon's FIOS...
  20. Antworten
    7
    Hits
    1.849

    Lost Connection of Lan

    I have a P3 and I am using a wireless bridge to connect to my network. i had manually entered the ip address and everything was working fine. After the latest firmware upgrade i lost my settings so...
  21. Antworten
    9
    Hits
    2.236

    yes both lights on the back are glowing. i...

    yes both lights on the back are glowing. i unplugged the ethernet line and plugged it back in and still nothing. i then decided to put in the address manually, i went into the system tab and...
  22. Antworten
    9
    Hits
    2.236

    I logged into my router and see the that the...

    I logged into my router and see the that the Profilux3 has an assigned ip but it lists it as an inactive connection.
  23. Antworten
    9
    Hits
    2.236

    no i have not, i followed these steps: onnect...

    no i have not, i followed these steps:

    onnect to your ProfiLux with ProfiLuxControl via your USB to serial adapter cable, go to System and select LAN and click to "Configuration... "
    Select...
  24. Antworten
    9
    Hits
    2.236

    I got a wireless bridge setup and plugged in the...

    I got a wireless bridge setup and plugged in the P3 and there is still no connection. i checked the connection through my laptop and i have connection so it has to be somewhere in the P3...
  25. Antworten
    9
    Hits
    2.236

    I think i have to buy a wireless access bridge to...

    I think i have to buy a wireless access bridge to connect to my wireless network and from there i can hardwire to the P3. I think this will work...any info?
Zeige Ergebnis 1 bis 25 von 33
Seite 1 von 2 1 2