Search:

Type: Posts; User: Laith_61

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Question re humidity sensor controlling 0-10v

    I have an air temp/humidity sensor connected to my P4. I have the humidity level determine the 0-10v output (via the IO Box) to an extractor fan that extracts air from above my tank to the outside....
  2. Replies
    7
    Views
    882

    It was a good idea but as you can see above, the...

    It was a good idea but as you can see above, the settings of the switchbars are all OFF so that it the way they need to be.

    It must be something else, unless I have misunderstood how this feature...
  3. Replies
    7
    Views
    882

    It was a good idea and thanks for pointing out...

    It was a good idea and thanks for pointing out that feature for me. I might use it for my return pumps!

    Any other ideas from anybody?

    Laith
  4. Replies
    7
    Views
    882

    Actually, in rereading the instructions, ticking...

    Actually, in rereading the instructions, ticking the solenoid sockets means that they will switch ON in the case of a recovery from a power failure?

    If so, I don't want that and in that case the...
  5. Replies
    7
    Views
    882

    Thanks for the quick answer. I didn't even...

    Thanks for the quick answer.

    I didn't even know that this option of configuring the Switchbars existed!

    But when I look at all three switchbars, all of the sockets are NOT ticked.

    So should...
  6. Replies
    7
    Views
    882

    Level sensor behaviour when power out

    Last night the lights in our house flickered for about a second and then stayed on. It must have been some type of power fluctuation or very brief outage.

    Of course this meant that everything...
  7. Replies
    8
    Views
    3,620

    I'm having the same problem. Even in the sensor...

    I'm having the same problem. Even in the sensor data chart it just shows a horizontal line unless I choose "Fullscreen mode on/off". And the KHD data is not available at all, just giving me a "No...
  8. Replies
    4
    Views
    3,571

    Ok, that makes it much clearer. So as long as...

    Ok, that makes it much clearer. So as long as the PBT is not set lower than the illumination channel setting then the illumination channel setting does not change. However any increase in the PBT...
  9. Replies
    4
    Views
    3,571

    Thanks for the reply. Just to be clear: If...

    Thanks for the reply.

    Just to be clear:

    If I lower the PBT of the green channel from 100% to 80% won't that lower the actual green channel output to 80% of 12%, or to 9.6%?

    Or is it that as...
  10. Replies
    4
    Views
    3,571

    Mitras LX 7206 Power Balancing question

    I posted this question at the tail end of another query I had but I think it better to start a new thread on it...

    I'm not very clear on how exactly the Mitras LX 7206 power balancing works:
    ...
  11. Replies
    6
    Views
    3,410

    A follow up question: I want to boost the blue...

    A follow up question:

    I want to boost the blue channels to 110%. I currently have the blues at 100% and red and green at 12% in the illumination channels.

    I can just change the blue channels...
  12. Replies
    6
    Views
    3,410

    Ok, thanks Vinny!

    Ok, thanks Vinny!
  13. Replies
    6
    Views
    3,410

    This is what I see at the bottom of the list when...

    This is what I see at the bottom of the list when I click on the illumination tab in the GCC (connected to the P4):
    12206

    There is no energy option...

    Does this mean that I have to connect to...
  14. Replies
    6
    Views
    3,410

    Can't find energy options in GCC?

    I want to change the energy options on my five Mitras LX 7206s but I cannot find the energy option item in the GCC when I log into my Profilux 4.

    Where can I see these options (to change the...
  15. Replies
    2
    Views
    4,655

    Hello Vinny, Yes, that's the expansion card I...

    Hello Vinny,

    Yes, that's the expansion card I have in the P4 (PLM-4L, the one with two L ports). So without a Y splitter on L3/L4 of the Expansion Box whatever is connected in that port would be...
  16. Replies
    2
    Views
    4,655

    PropellerBreeze 3-6 not working correctly

    (I can't seem to open a ticket using Firefox so I'm posting this here)

    I purchased a third PropellerBreeze 3-6 and installed it. However, it pushes almost no air, even when 10v is sent to it via...
  17. Hello Vinny, I just tried to open a support...

    Hello Vinny,

    I just tried to open a support ticket but when I click submit ticket I just get the spinning wheel (this is the second time in a row that I cannot open a support ticket...).

    Could...
  18. Bump... Anybody have any ideas?

    Bump...

    Anybody have any ideas?
  19. Cannot get the Profilux 4 to connect to Mitras!

    I am at wits end!

    I have five Mitras LX7206 units that I set up several weeks ago. At that time, my Profilux 4 was still running my old tank so I set up the Mitras with one being the master...
  20. Replies
    4
    Views
    11,876

    :) I was wondering if the symptoms that I...

    :)

    I was wondering if the symptoms that I described indicate a power problem...

    It's strange, usually when the PSU defective no electricity passes to the device?
  21. Replies
    4
    Views
    11,876

    I just tried a power supply from another of the...

    I just tried a power supply from another of the Mitras on the light and now it works.

    Bad power supply?
  22. Replies
    4
    Views
    11,876

    New Mitras LX 7206 not tur?

    I just plugged in one of my new Mitras LX 7206 and the following happens:

    - The GHL logo blinks blue
    - The fans turn on and then off about every second
    - The display is blank (dark)
    - The...
  23. Fantastic... Thanks Pit, your help is much...

    Fantastic... Thanks Pit, your help is much appreciated!

    Soon I will also have the question as to how to program the Profilux to manage the extractor :-)

    But I will start a new thread for that...
  24. How do I wire this extractor fan to GHL BoB?

    I am installing a variable speed air extractor above my tank which will extract humid air to the outside. I want to run the extractor via my Profilux 4 and control the speed depending on the...
  25. Replies
    2
    Views
    6,922

    Great, thanks Pit!

    Great, thanks Pit!
Results 1 to 25 of 75
Page 1 of 3 1 2 3