Thank you very much. I'll do that just in case.
Type: Posts; User: Monihdez
Thank you very much. I'll do that just in case.
Thank you very much for the quick reply.
On the second question I was thinking more about problems when transferring the settings back to Profilux. Because there is such a big gap in Firmware and...
Hi
I want to upgrade from firmware 5.11 to 6.05. After checking on here it looks like I need to do the update from PLC 5.x.x and then connect with the new PLC. Is this correct?
There is one...
Hi
Thank you very much for your responses.
Ashlight, mdanielse could you post links to the threads you refer to, please?
Carolin, would you be able to check with Matthias, please?
Thank...
Hi
I want to upgrade from firmware 5.11 to 5.15. I have a PAB bar attached to the profilux 3 but I am not sure if I need to disconnect it during the upgrade and then assign it after. I recall...
I am also still very interested in this. I am at the moment using a turkey baster every couple of weeks as sedimentation is becoming more of a problem.
I know there are lots of things in the wish...
Hi Matthias
The Tunze controller I have is the 7096. The exact sequence of the pumps for the desedimentation storm is described on page 101 of the manual below
...
Thanks Matthias. Would you be able to tell me how high in the priorities is this? I am only asking because I was going to sell the Tunze controller now that I have the profilux controlling my pumps...
Is it not possible to do this with the Profilux? Please does anybody know?
Thanks
Did you find out if this is possible? I am trying to do something similar.
Thanks
Hi
I have been trying to simulate with my profilux something that I used to do with my Tunze controller: a desedimentation storm. It is just running the tunze pumps in a certain (different)...
I cannot see how to vote using tapatalk, sorry. I have an AI sol blue.
Thanks. I'll have a go at making one.
Cheers
Hello,
Is it possible to stand a PAB plugbar vertically on the floor? Is there a base that I can attach to one end of the plugbar that would allow this mounting position?
Thanks
Hi Matthias
Sorry, yes I found that bit. Even though I had been looking for ages at the code I did not see it until I posted it here. Typical!!
It is the other bit, the one about the switches...
I don't think you need the < p> and for an email only when writing webpages (HTML)
Mine also has [xx] instead of [x]. not sure if that would make a difference.
Thanks Wirus, that was my first thought as well but I have the latest Firmware, 5.11. I have managed to configure the use of PLC from outside the house so I guess it is not that important because I...
Sorry, me again.
It is the SWIC token to display the current of the switch. If I take it out it works. Could it be because the first four switches are the dosing pumps and the PAB bar starts at...
Hi
I am trying to set up sending emails from my profilux. I have copied the message above and what I get from a test is the following which is not quite right
no alarm - all OK
Sensors...
Thank you very much that makes a lot of sense now!
Thank you very much for that Gazz. So that would be helpful for automatic water changes for example, am I right? Any other examples where this might be used?
Hi
I have just installed an optical level sensor and I have a couple of questions about the options in PLC to set it up.
"maximal on-time": Is this a safety feature so that if the sensor fails...
No, it shouldn't. All I am saying is that I had the same problem and that's what I did. It worked although it might have been a coincidence of course.
No, do not connect it to the profilux yet. First you need to configure it. The VAP11G can be powered in two different ways
1. Using the USB attachment
Or
2. Connecting it to the mains using the...
Just one more thing to try. Disconnect the USB. Use the power lead of the profilux to power the VAP11G (make sure that you do not connect the USB or you will fry the computer) and try again. I had...