Dear Carolin,
you didn't answer my question: are my ADC values acceptable, with a difference of about 100 between ADC1 and ADC2?
I have calibrated correctly redox probe. The value measured in...
Type: Posts; User: mistral
Dear Carolin,
you didn't answer my question: are my ADC values acceptable, with a difference of about 100 between ADC1 and ADC2?
I have calibrated correctly redox probe. The value measured in...
I have calibrated my new redox probe, linked to my profilux 3.1N ex, and I have had these calibration values:
Value 1 0mv ADC1 450
Value 2 220mv ADC2 549.
Are they good? It is enough a...
Here my screenshots of level menu and system menu. What is the next step to set correctly PLM4 levels?
6017
6018
6016
Dear Frank,
I have read the expansion box version by clicking on it in the system menu of profilux control software.
Where can i check the correct expansion box firmware using profilux control...
Dear Frank,
I have obviously reassigned my expansionbox that is 1.08 version. Can you help me with the correct settings step by step?
I have inserted 3 extension cards on my expansion box linked to a profilux 3.1N ex: 1 PLM-CondS in the first slot, 1 PLM-pH-Temp in the second slot and 1 PLM-4Level in the third slot. I have...
Dear Matthias,
I have level sensor 5 connected. My question is: how can I understand the state of a level sensor from the number of the sensor? I mean, if a sensor detects water or not, how does the...
Sms with status report includes all probe values, and sms ends with 'Level: 56'. What does "Level: 56" means? What is "56"?
My sms module has last firmware.
Thanks in advance
And how about the other probes?
Thanks Matthias.
But, after what time the probes are no longer reliable, and the measured values are not accurate?
They read the correct values in the calibration fluid. When the calibration ends, I check always the value measured in the last calibration fluid (9) and the value is correct!
I have 2 pH probes, one connected to the expansion box (pH2), and the other one connected to an extension slot in the expansion box (pH3).
I have calibrated both probes in the same solutions (7 and...
I have just updated the firmware of my sms module.
Now, status report includes all probes I have, but sms ends with 'Level: 56'. What does 'Level: 56' means?
My sms module is connected via RS232 and has version 2 firmware. My profilux has 6.06.
Do I need to install last firmware in sms module? It is possible through profilux control software?
I have my probes connected to the expansion box, and they are named pH2, temp 2, co.S 2 and redx 2.
When my sms module sends to me the status report, the sms includes only the 4 values from the...
What are PCBA? Did you replace them by yourself?
I have hade a problem right now after a strong thunderstorm. My profilux turned off by itself (maybe power surge on ethernet cable).
I have tried to turn on again my profilux, and some messages...
I want to turn off one socket (my skimmer) when a level sensor registers a high water level in the sump, and trigger an alarm. It is possible? What is the correct setting to do that?
Thank you...
So, I can save all my Profilux settings by ProfiluxControl 5.x and update to firmware 6.05. Then, I have to use ProfiluxControl 6.x to re-transmit all settings to Profilux. That's right?
I have 5.15. Can I update to 6.05 firmware version directly or i need to install an older version before?
Thanks to all.
I managed to access to profilux from remote pc (through web interface), but not from android app: connecting, retrieving data, no response from the device!
Do you know what is the...
I have a profilux 3 ex and i don't know how to connect my profilux to internet for remote access (from computer and from smartphone). Can anyone help me step by step and say to me all necessary...
OK. Thanks a lot!
My expansion box version is 1.08. Does it work, or i need to update firmware?
I have installed some additional measurement cards in my expansion box (1 ph, 1 cond, 1 temp and 4 level sensors). After reconnecting and turning on my expansion box, profilux didn’t detect any new...