Search:

Type: Posts; User: The Codfather

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    2,308

    Ok, I found it. You have to go into expert mode....

    Ok, I found it. You have to go into expert mode.
    Now the redox I set up fine, but I found a few problems when trying to set the temperature.
    1-I cant change the spread 0C-40C, that's it, I change...
  2. Replies
    2
    Views
    2,308

    pH and redox readings

    Does anyone know if we can change the values for the graphs on the touch when it comes to these values. I know the pH of the aquarium will swing, but I do not need a range from 4 to 10 on the graph....
  3. Replies
    1
    Views
    3,550

    A little more reading I guess. Expert Mode is the...

    A little more reading I guess. Expert Mode is the answer.
  4. Replies
    1
    Views
    3,550

    Profilux touch 1.05

    Hey, hoping someone can help me. I was wondering if there is display illumination in the firmware that would allow me to drop the screen out to 0% over night. I see it was in previous versions, or am...
  5. Replies
    2
    Views
    2,328

    M4x12mm I think.

    M4x12mm I think.
  6. Replies
    2
    Views
    12,053

    Thanks for the info Vinny. Now can I put two PWC...

    Thanks for the info Vinny. Now can I put two PWC cards in one profilux? or would I have to separate and run the second P3?
    Guess Ill be doing another order in the next little bit, have to get it...
  7. Replies
    2
    Views
    12,053

    PWC and multiple tanks

    I recently bought out a system, it included a couple of mitras and a complete P3, bonus. Thinking I may set this other tank up beside my existing tank but would like to have the lights set a little...
  8. Replies
    6
    Views
    3,325

    Thanks Vinny.

    Thanks Vinny.
  9. Replies
    6
    Views
    3,325

    Sorry Doc, found someone on our local forum to...

    Sorry Doc, found someone on our local forum to trade with already.
  10. Replies
    6
    Views
    3,325

    Changing 6200 to 6100

    I am going to be changing out my 6200 pucks for the 6100 series soon. Is there anything that has to be done prior to changing the boards out? I know I can change the settings in GCC to have the...
  11. Replies
    13
    Views
    7,900

    I've always been able to connect through USB. The...

    I've always been able to connect through USB. The problem was with LAN. I've got CAT5e almost everywhere in the house, so easy to have my lap top hooked up and check or adjust the programming. I...
  12. Replies
    6
    Views
    3,295

    Tried a few different things in the last week,...

    Tried a few different things in the last week, seems i can only get a stable connection with FW6.14 and GCC1075.
  13. Replies
    13
    Views
    7,900

    I don't think windows is the issue anymore. I...

    I don't think windows is the issue anymore. I think there is a problem with FW 6.19 and GCC 1075.
    I knocked down to FW 6.14 and was able to connect via LAN immediately, with no issues since.
  14. I dropped the FW down to 6.14 from 6.19. I...

    I dropped the FW down to 6.14 from 6.19. I instantly was able to connect via LAN again.
    I am still using GCC 1075, so I'm thinking there was problems with communication between the GCC1075 and the...
  15. I am having constant problems with GCC "Not...

    I am having constant problems with GCC "Not Responding", and then kicking my connection with an Error 50.
    Thought that Id had enough of windows 10, as Ive had nothing but problems with it since the...
  16. Replies
    13
    Views
    7,900

    Well, tired of all that windows 10 crap. Back to...

    Well, tired of all that windows 10 crap. Back to 8.1
  17. Replies
    2
    Views
    1,746

    Well, unplugged everything, plugged everything...

    Well, unplugged everything, plugged everything back in. Rechecked everything, and bing. Connected.
    Maybe just a bad connection some where, but all is good now.
    Thanks
  18. Replies
    2
    Views
    1,746

    LAN Connection

    I have in the past always been able to connect with my P3 through the LAN. I recently updated my computer, and since then I have not been able to successfully connect using LAN.
    Is there a driver...
  19. Replies
    3
    Views
    2,780

    Should be able to update through Control centre...

    Should be able to update through Control centre under PAB.
  20. Replies
    3
    Views
    2,698

    you need to have two drivers. This looks like the...

    you need to have two drivers. This looks like the problem I had a while back, have a look at this thread.
    http://forum.aquariumcomputer.com/showthread.php?9837-Failing-to-upload-new-software
    Im...
  21. Replies
    13
    Views
    7,900

    Having connection issues as well. At first it...

    Having connection issues as well. At first it seemed to be fine, but now...cant seen to connect with RJ45, only with USB.
  22. Im thinking its windows 10. I never had any...

    Im thinking its windows 10. I never had any problems prior to windows 10 for hook up. Updated both FW and GCC to latest versions, never a problem with 8.1. now, have to try two-three times with USB...
  23. May i ask what version of windows you are running?

    May i ask what version of windows you are running?
  24. I think i am having the same issues with windows,...

    I think i am having the same issues with windows, have to try multiple times for a connection. finally have success with a USB but not with RJ45.
    Could this be the FW?
  25. Replies
    6
    Views
    3,295

    Alright, I tinkered about tonight. Seems I...

    Alright, I tinkered about tonight. Seems I finally got a stable connection with USB. Tried RJ45, as that's how I normally check my setting, but still cannot connect. No error codes, but no...
Results 1 to 25 of 55
Page 1 of 3 1 2 3