Thanks I will check with Progressive on the tubing. I have ordered from big al in the past also. I am getting the 3 BM chambers/containers also - they are included as part of the small balling kit -...
Type: Posts; User: Aqualab
Thanks I will check with Progressive on the tubing. I have ordered from big al in the past also. I am getting the 3 BM chambers/containers also - they are included as part of the small balling kit -...
Okay, good to know.
I am ordering the small balling kit and the third motor/pump housing for my doser today from Progressive. Where did you get the tubing that you used on your system - doesn't...
Thanks Michael - I did not have the socket set to timer 7 & 8 respectively - they were both set to 1 (I never changed them within the program - duh!). Works now and verified operation.
I think I...
Pro Plus II, Slave doser, latest firmware and software installed. I still cannot get the doser to run after multiple programming attempts. I have it set up this way:
The power bar is programmed 1-6...
No big deal, thanks for heads up on upcomming version.
Thank you - issue resolved using the RS485 solution.
RS485 delay worked - quick connection and response within program!
Thank You
5.00o is for Pro 3? I have a Pro II. I have 5.00m with 5.011 software, latest versions per download for a Pro II.
Same problem - Pro II also. Cannot connect with 5.011 at all. Using 5.09 and 5.00m - very slow when it finally does go through. Sometimes I just get a non response also. New GHL USB card/connection....
I am set up using the GHL USB card with correct driver software for windows version. I have installed the 5.09 software and 5.00m firmware. 5.011 doesn't connect at all, getting error 28 message all...
I went back to 5.08 and it works fine, not slow, connects quickly. So i am now using 5.00m and 5.08. So I have established that the problem is not with my laptop but with the upgrades. Guess I will...
it finally connected - very slow to connect - menu is slow, whatever I select is slow to pop up. What is causing this?
I set baud to 9600 for the USB device in manager and the connection speed in control manager - starts to connect (green bar slowly moves to right) then it freezes, i get a not responding message at...
I tried using a different USB port on my laptop - recognized as comm port 7 in manager. Profilux control started to communicate (green bar moving very slowly) after a long time it said comm...
I noticed that the PLM-USB windows 7 driver says Prolific USB to serial comm port (Comm 6) Port_#0002.Hub_#0005 in my device manager? Shouldn't it be USB to USB? The device manager also says Comm 6...
Yes, latest driver. I have windows 7 on my laptop. The CD that came with the GHL USB module did not have a windows 7 driver on it.
It is a PLM-USB
I have used just one USB port throughout initial install and upgrade process - kind of dedicated it. It is still coming up as com port 6 in the GHL program and in the device manager. Just won't go...
Checked the settings immediately after download - no changes.
Installed version 5.0.0.11 to see if it makes any difference - did not. Continue to get error code 28 when trying to connect via USB.
Your'e welcome.
I downloaded firmware version 500m just now and it loaded successfully. But now I can't connect - error message 28! I am using version 5.0.0.9 software because 5.0.0.10 hangs up on...
Need some help here please.
Profilux Plus II - Digital Power Bar - Slave Doser (two pump)
S1-S4 connection. Pump runs in manual mode overide.
I have the dosing pump plugged into socket/outlet #1...
I keep getting this error message below while trying to download firmware version 500m. Profilux Plus II
Error while transmitting firmware!: flasherase - no response - 8
I am using software...
It was Moonphase - thank you aqua_digital. I'm not going to even ask why that would have overidden the programming and kept the lights at 1%. Did not see that described in the manual either. I think...
I can manually manipulate light intensity for both Illum 1 & 2.