It'll be $73.90.
https://www.aquariumcomputer.com/usa/product/kh-director-ph-electrode/
Type: Posts; User: Jerel1
It'll be $73.90.
https://www.aquariumcomputer.com/usa/product/kh-director-ph-electrode/
Answer is within the first post, last sentence..
"Sending emails is included now, however token support is a bigger job and not yet available, comes in the next update."
Pressing the "Cancel Button" on the ProfiLux itself should be enough to initiate Feed Pause, no?
Correct, that'll be fine in order, either way. Just be mindful to leave the last PAB device with one PAB port free of a connection. There is an example of how to connect PAB devices within the...
Hi,
You can control up to eleven(11) Vortech Pumps.
The VorTech Controller comes with just the controller itself. You will need to acquire the appropriate length of PAB cable to fit your...
It appears that you have the sensor mounted vertically. The appropriate position of the sensor should be horizontally mounted to operate reliably.
That'll be a USB type A to B that you didn't receive ? It came with a type A to A? Lol
I have full control to switch between modes and flow outputs at any programmed schedule.
I cannot speak for everyone, but there are no communication, nor pairing problems with my mp40QD. The only noticeable issues are viewing the Status/Firmware #/Pump Type of the pump within -GCC-...
Even with the latest firmware and software. The pumps pair successfully and functions by commands.
I believe you're looking at the firmware for Powerbar 5.1, which is 1.01. Powerbar 6D latest firmware is 1.08.
Common sense... Firmware 6.27 for ProfiLux is bundled with GCC 1.0.8.4.
Correct, GCC 1.0.8.2 became a normal release on February 23rd.
I ended up re-flashing the Doser 2, ProfiLux and reinstalling GCC.
Changes..
Doser 2 now pulsates white LED in Slave Mode
Doser 2 pulsates white and red when being assigned to ProfiLux, Alarm.
Correct,
Doser 2 -FW1.17
ProfiLux -FW6.25
GCC -FW1.0.8.2
I'll try to re-flash the firmwares again and install reinstall GCC tonight.
After all this is a Beta release..
Ok, assignments were made by assigning the Doser 2 to ProfiLux for the first few attempts. I tried both directions after no success.
I have a Vortech Controller and a 5.1 Powerbar that...
Shouldn't i be able to see communication between the Doser 2 and the ProfiLux via GCC-Doser 2?
8199
Only if i assign from the ProfiLux do i make communication, though. I still have the PAB...
You are absolutely correct!
Doser 2 printed S/N is 141108(1)030
GCC via Doser 2 displays 141108(1)030
GCC via ProfiLux displays 141108(2)030
How do i change the S/N from the ProfiLux?
Saul831,
Latest firmwares are packaged with nearly every GHL Control Center release. You can find the recent release within the downloads page, including information regarding change logs.
...
Navigating to -----> PAB --- Doser 2 Slave /Configuration../ *The PAB device is not responding*
I have preformed a factory reset to my Doser 2.
I've unassigned and reassigned the Doser 2 as a PAB...
Where is the appropriate section to provide feedback regarding this Beta release?
My ProfiLux 3.1T- FW6.25 responds with an alarm of PABCOM when my Doser 2 Standalone-FW1.17 is configured as Slave...
How did you setup a wireless connection for your Doser 2?
What are you experiencing with the GHLControl app when you are attempting to connect? Error message? No response? Crashes?
hunt1Matthew,
Connection Name is where you input a name/number for your Doser 2 via your iPhone.
Correct, Hostname is the IP address of the Doser 2.
http://forum.aquariumcomputer.com/showthread.php?10605-VorThec-MP40-and-VorTechController-connections-problems&p=65856#post65856
Feedback on the matter?