And a wish list for future extensions :
Possibility to turn off one of the 6 led pads when one is just on top of water extraction pipes.
+master and slave relative position declaration so that...
Type: Posts; User: Maverick38
And a wish list for future extensions :
Possibility to turn off one of the 6 led pads when one is just on top of water extraction pipes.
+master and slave relative position declaration so that...
Hello,
I just wanted to know if there is anything like a break in period for the Leds to give full lux output ?
And another question : when switching from 2x250W HQI to 2 mitras, what would...
A quick look at the manual of the PII will probably be sufficient ;)
I have just found there the calibration process for the ORP probe and it solved my problems ... :)
Mav'
After many attempts I managed to find someone who has read the Profilux 2 manual (I had only read the PIII manual so far) which is way more detailed than the PIII manual and explains in details the...
Hello,
yes, all sensors including the pumps and the PAB powerbar were removed when it crashed.
Mav'
Yes and it worked after looking for a PC with RS232... too bad it does not work -yet ^^?- with USB .
The process described in :
http://www.aquariumcomputer.com/Forum/showthread.php?t=1274
worked...
Hello,
I have updated the prolific again and it seems that the USB behavior was OK.
With the Profilux controller v12.
From this success I tried to update the firmware but the controller...
Hello,
In terms of port I have checked I plug the right probe in the right socket.
Do you think I could plug the PH probe into the Redox socket to make sure the port works on the PIII side ?
...
New update
I have the impression that in order to satisfactorily calibrate the probe there need to be an established connection between the PIII and the sump :
by this I mean that the potential...
Hello,
I tried to update my PIIIex.
It failed but without impacting the use of the PIII (ouf!)
First Question :
The PIIIex shows a firmware version 5.001 when it boots is this the latest one...
Hello,
I have just tried to calibrate my Redox probe (PIIIex and probe are new).
and it gives the following results :
whether the probe is unplugged the value ADC read is 531mV
and when I plug...
Hello,
I have read on an american site that a dimmable Profilux controllable ballast was being developped ?
That would be great !!
Is there any confimation of this from GHL ? Would this be...
All right !
Now it works !
I can access my profilux from all my PCs at home after bridging the wireless connection !
many thanks to all who helped !
Now the second part that I need to...
By device do you mean "network card" or Computer ?
The Laptop has 2 network card : one wireless and one LAN.
I have set the IP to static so I should expect the 2 network card to have the same IP...
Yes , agreed this is what I have done :
the IP of the laptop is set to 192.168.1.1
the profilux is set to 192.168.1.70
The Laptop is indeed connected via its 2 network cards :
Wireless : IP...
You were right, I have disabled the DHCP.
But now my Laptop does not connect at all with the PIIIex :
IP is 0.0.0.0
Subnet is 0.0.0.0
Gateway is void
(It still connects wirelessly to the...
Yes, but before going the bridge and wireless way,
the first step is to be able to connect to the PIII via the RJ45 cable and this very first step does not seem to work for the moment...
Mav'
Hello,
My config is the following :
IP of my Laptop :
192.168.1.1
IP of Heavy PC :
192.168.1.2
Router (default gateway) :
192.168.1.254
Hello,
My configuration is the following :
One 280L tank ^^
One "Heavy PC" connected to my router both pieces being distant from the tank
One laptop (that can be wirelessly connected to my...