Ok, thanks Vinny.
:)
Type: Posts; User: MitchM
Ok, thanks Vinny.
:)
Sensor is 12 years old.
I keep the sensor clear of debris as needed and clean the sensor face with a toothbrush as needed - not very often.
The water level sensing feature has stopped working correctly.
When the water level drops below the sensor, nothing happens. If I unplug and then plug back in the controller, the water topoff...
I am happy to update that my Profilux system is up and running again on GCC 1.0.7.7, the P3 is updated to firmware 6.22.
The steps I followed are
Downgraded to GCC 1.0.7.2, P3 firmware upgraded...
I have tried many different combinations of firmware for the P3 6.18. 6.22 and GCC down to 1.0.7.2, back up to GCC 1.0.7.7.
The only sensors I can get to display on the sensor page are PH1, Temp 1...
ok
Thank you Lasse
I'll try that next.
Hmm.
Now GCC won't even let me see the system layout connected via either LAN or SERIAL.
As soon as I click on the system item, GCC disconnects me from the P3 and I get an error code 41
I...
Power off for 10 seconds has left me with GCC showing 1 PH sensor, Temperature 1 and Temperature 2.
PH is reading 10.5
Temperature 1 probe reading correct temperature
Temperature 2 probe reading...
The update to 6.22 did not go well.
The P3 no longer recognized the conductivity probe or the PH probe. Only the temperature probe displays on the GCC software.
I downgraded the P3 to 6.18, but the...
I had previously backed up the sensor and settings data.
I transmitted the sensor and settings data to the updated P3 and the P3 is working again.
Thank you PIWAWT, that got me 1 step further.
I now have the P3 display flashing "Einstellungen rueckgesetzt!!!"
The GCC tells me that the firmware was updated sucessfully.
.
I am trying to update my P3 firmware to v 6.22.
My computer is win 10
P3 is firmware version 6.11
GCC is 1.0.7.7
The P3 is connected via serial connection
When I try to update the P3...
Merry Christmas and a happy new year!
I have a Mitras 6100 that has a message on the main screen and GHL Control Center program that tells me it "is a demo unit and not for resale".
How can I get rid of this message?
.
This is very interesting.
Thank you Gunther.
When plugged in, the plug outlets read 14.2A, 14.6A, 14.8A, 14.8A respectively.
When unplugged, the reading remains the same.
The power bars are plugged into battery backup units so power...
I'm going to bump this thread up.
I have a feeling it's been forgotten about.
A reply would be appreciated.
Hello,
Is there any answer?
Yes, PAB power bars.
The Powerbars have different numbers and the sockets can be switched independently.
On 1 power bar, problem socket is #6
On 2nd power bar, problem sockets are #7,8,9.
Hi,
I have 2 6D power bars that have 4 DC pumps plugged into them and lately the amperage readings are displaying over 14 amps actual current for each pump.
They used to display less than 1 amp...
Great, thanks Gunther.
Yes, it is a PL3.
As the title says...
I have:
P3 with level sensor hooked up
1 Expansion box without level sensor hooked up, but with a level sensor port
2nd Expansion box with a level sensor hooked up
The...
Hello,
I was able to solve the problem and all three units are now updated to the latest firmware.:)
For the last 4 or so years, I have been using this USB adapter:
It has worked for all other...
-First updated P3 to 5.17
-I powered off the powerbar
-Clicked on "update anyways?"
-Immediately turned on powerbar. (maybe 1 - 2 second delay)
-Yellow light on powerbar flashed a few times...