Search:

Type: Posts; User: pjcook

Search: Search took 0.01 seconds; generated 23 minute(s) ago.

  1. All fixed.

    Hi Idid a full factory reset and was able to setup correctly.
  2. Step by Step on setting up Mitra's Light Bar2 on Profilux 4 please

    HI

    I am having lots of issues trying to get my Lightbar2 Daylight.

    I am using the splitter, communications cable plugged into the Digital Light Controlled Interface.

    I have managed to get...
  3. Replies
    4
    Views
    2,464

    Could well be the case as I was using the unit...

    Could well be the case as I was using the unit previously on a marine tank, there was no message that the calibration had failed but I take your point. I will order a new probe and see if that sorts...
  4. Replies
    4
    Views
    2,464

    Hi I have run the calibration twice and still...

    Hi

    I have run the calibration twice and still the same issues. The unit is about 2 years old. The ADC Values are ADC 1: 530 ADC 2: 522
  5. Replies
    4
    Views
    2,464

    Issue with PH Calibration

    I have just calibrated my PH probe for freshwater, I set the first level to 4 and used calibration solution 4 and the second level to 7 and used calibration solution 7. All went well with the...
  6. Replies
    7
    Views
    2,755

    Hi Mathias I suspected that would be the case,...

    Hi Mathias

    I suspected that would be the case, it is not a big issue as I can do most things from the remote function using the software. One further question, can I do firmware updates safely...
  7. Replies
    7
    Views
    2,755

    The display on the unit is corrupted. I can read...

    The display on the unit is corrupted. I can read some of the words OK, but when trying to configure the unit it is impossible to read everything correctly.

    I did a factory reset, but that did not...
  8. Replies
    7
    Views
    2,755

    Thanks, can you also advise if a firmware update...

    Thanks, can you also advise if a firmware update may help fix the display issue?
  9. Replies
    7
    Views
    2,755

    Calibrating PH probe using PC software

    I have just hooked up my profilux Plus II to my freshwater tank after it had been in storage for 6 months. Previously it had been calibrated for a saltwater tank. My problem is that the profilux...
  10. Replies
    2
    Views
    3,236

    Problem with Powerbar 6D

    I purchased and istalled a Powerbar 6D onto my Profilux Plus II. Initially it worked fine until last week. The powerbar now does not seem to be communicating with the computer. 1 Outlet S3 is...
  11. Replies
    17
    Views
    10,803

    Hi Matthias I have received the replacement...

    Hi Matthias

    I have received the replacement LAN card today, installed and connected first time without a hitch.

    Regards

    Peter Cook
  12. Replies
    17
    Views
    10,803

    Hi Matthias I agree, I have returned the card...

    Hi Matthias

    I agree, I have returned the card to my retailer, he is going to return it to be checked.

    Thanks for your assistance.

    Peter
  13. Replies
    17
    Views
    10,803

    I have plugged the LAN card into the same slot...

    I have plugged the LAN card into the same slot the USB card was in and still unable to connect. I have also tried all of the other slots as well.

    I have assigned a static ip address of...
  14. Replies
    17
    Views
    10,803

    OK, I found a computer with a Serial port and was...

    OK, I found a computer with a Serial port and was unable to connect using the serial port either. I have done a complete factory reset on the profilux and the serial port and USB port are now...
  15. Replies
    17
    Views
    10,803

    I have tried it using both WinXP and WIndows 7...

    I have tried it using both WinXP and WIndows 7 RC. The USB connection worked perfectly until I removed it to install the LAN card. I re-installed the USB Card so I could use the software while I...
  16. Replies
    17
    Views
    10,803

    [QUOTE=aqua_digital;1655]Then you need a cross...

    [QUOTE=aqua_digital;1655]Then you need a cross over cable to connect directly, it will not work without[/QUOTE

    I did use a crossover cable when I directly connected
  17. Replies
    17
    Views
    10,803

    As per original post, I have directly connected...

    As per original post, I have directly connected to the profilux LAN car with no routers or firewalls involved, still unable to connect.

    I have tried to connect using the USB interface I previously...
  18. Replies
    17
    Views
    10,803

    No I did not change the Baud rate at all. I...

    No I did not change the Baud rate at all.

    I have changed the configuration to 10 Mbps and still cannot connect.

    If the card is plugged into the middle slot on my profilux what Device Address...
  19. Replies
    17
    Views
    10,803

    Cannot connect using LAN card

    I am having a similiar issue to other users in trying to connect to the profilux II unit over my LAN.

    I installed the LAN card into Slot 1 and configured the card with an ip address of...
Results 1 to 19 of 19