I own six Mitras LX 7206 and I recently starting to have an issue with two of the units. In the past week, I have found two of them off in the morning. The display is completely dead but the GHL...
Type: Posts; User: mcrist
I own six Mitras LX 7206 and I recently starting to have an issue with two of the units. In the past week, I have found two of them off in the morning. The display is completely dead but the GHL...
I guess nobody else likes this idea.
I had my first failure last week and it turned out to be the power supply for the ProfiLux 3. This got me thinking and I wanted to see if anyone requested a redundant power supply for the ProfiLux...
This evening I upgrade all of my Mitras to 1.10 and then decided to try the WiFi module upgrade too. I have never done this upgrade before but the instructions seemed simple enough. All lights were...
I am excited but sad that it looks like I will need to replace my version 3 controller.
I was able to identify communication by two methods. The first is that the lights receives an IP address from my router and it updates DHCP table on the router. Second, my router displays traffic...
I own two Mitras LX7 lights and recently I ran into a wireless issue. I few months ago I was no longer able to connect to either light over a wireless connection. Wasn't a big issue until my cable...
Yes, I was using the original cable and I tried different USB ports on different computers. I have two Mitras so I tried the other cable. 24 years in IT and I have never seen a cable fail like this...
Same issue, no change.
Thank you for the quick reply. I installed the driver and I still have the same issue. I tried it on both the Windows 7 and Windows 10 laptops.
Mark
I am attempting to connect to one of my Mitras LX7 with a laptop and USB cable. On a Windows 10 laptop I receive a "Unknown USB Device (Device Descriptor Request Failed)" message and on Windows 7, I...
I am a new owner of 2 LX7's. I updated my GHL Control Center to the latest non beta release (v1.0.9.4) and I noticed that a new firmware was available for the LX7. When going through the firmware...
That did the trick, thanks.
I think you may be misunderstanding my question. The amount of time I set is not an issue and it is working perfectly for ATO. I am trying to have the ATO turn off two additional sockets/outlets...
When the water level drops below the sensor it will activate a socket which turns on a pump. If the pump is on for more than 1 minute and the water level has not reached the sensor, an alarm will be...
Any assistance would be appreciated...
I need some assistance with the programming logic.
I own a ProfiLux 3 with the optical sensor to control water level. This works perfectly but I would like to program the controller to turn off...
Thanks for the help. I did not have to do this in the past for firmware upgrades so I was surprised when it lost this information.
I just upgraded the firmware to 5.07b and the software to 5.0.7.3 and I ran into a problem, I lost my VorTech overview menu. I don’t understand why that disappeared but all other settings are fine. ...
PAB sounds good to me but I really don’t care as long as get the functionality. You could send me a module and a roll of duct tape and I would be happy.
No problem, I am happy to see I am not the only one. It’s still a great product, even if it takes me 30 minutes to do the hardware upgrade and 3 hours to reprogram it.
I do not wish to be negative but I have never been very impressed with any of the documentation. After I read it I usually need to just sit there playing around with the interface until it works. ...
Thanks that was it. This was the first time I tried the firmware update and I must say it could be improved, I am glad I don’t have to do that much.
I just got my ProfiLux III upgrade kit and I got everything working but the dosing pump. I am using firmware version 5 but no matter what I do I can’t get the dosing pump to display in the...