Search:

Type: Posts; User: Skydivingcatfan

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    6,586

    The only time I have had it happen is when I...

    The only time I have had it happen is when I unplug the light and that has only happened to one light a couple times.
  2. Replies
    19
    Views
    6,586

    Unplug the connector between the power supply and...

    Unplug the connector between the power supply and the light.
  3. Replies
    2
    Views
    1,200

    You should add that to the popup that ask to send...

    You should add that to the popup that ask to send the crash report.
  4. Replies
    2
    Views
    1,200

    Crash Reports

    Do the crash reports get used when they are sent? I have sent a few and never received a response or acknowledgement.
  5. Replies
    7
    Views
    4,906

    I wish they would get them in the SicceUSA store....

    I wish they would get them in the SicceUSA store. I was told they would be there in 8 -10 days a month ago.
  6. That is how I have my ATO set up on switch 64. ...

    That is how I have my ATO set up on switch 64. So if I make my maintenance event shut off switch 64 the ATO will not work during the maintenance event.

    How do I do it for the pumps that are on a...
  7. Turning doser off during maintenance event

    I am trying to figure out how to turn off my doser pump that I have set up as a ATO when I do a water change. I have the maintenance event set up and it turns off my return pump and flow pumps but I...
  8. Replies
    17
    Views
    5,653

    Thanks

    Thanks
  9. Replies
    17
    Views
    5,653

    I can not figure out how to turn this on. I...

    I can not figure out how to turn this on. I updated my firmware on my P4 to 7.28 the app on my iPhone is 3.13.5

    The instructions say "you can enable the feature in the app settings page" Am i...
  10. Replies
    2
    Views
    2,379

    Think I figured out why Filter not activated = 1...

    Think I figured out why
    Filter not activated = 1
    Maintenance not activated = 0
    I did not see that in the manual

    Edited to add

    I should have read the manual closer
  11. Replies
    2
    Views
    2,379

    Got it to work had to switch the feed/filter to...

    Got it to work had to switch the feed/filter to delayed on and remove the invert function.

    I do not understand why though.

    13012
  12. Replies
    2
    Views
    2,379

    GHL Programmable Logic Check

    Building on the GHL example of a delay on after maintenance mode trying to get this to work for 2 maintenance modes and 2 feed/filter modes. The delay times are not what will be actually used just...
  13. Replies
    7
    Views
    4,906

    I did not think so but was hoping I was missing...

    I did not think so but was hoping I was missing something.
  14. Replies
    7
    Views
    4,906

    Sicce Syncra ADV

    I meant the Sicce Syncra SDC not the ADV

    Can these pumps be controlled by a Profilux 4?
  15. This is good write up on what is measures. ...

    This is good write up on what is measures.

    https://www.aquariumcomputer.com/knowledge-base/conductivity-salinity-calculators-vs-profilux-calculated-values/
  16. Replies
    1
    Views
    1,277

    Sensor Sample Rate

    Why do the sample rates vary? I have the setting for a sample every 10 minutes but when I look at my data the rates are all over the place from the 10 minute setting all the way to 60 minutes. The...
  17. Replies
    5
    Views
    2,565

    The screen was on the whole time. I shut it down...

    The screen was on the whole time. I shut it down at lunch and it was still displaying the screen from 6:47 am
  18. Replies
    5
    Views
    2,565

    GHL Connect Dashboard refresh rate

    Trying to get familiar with my GHL products. Pulled up the GHL connect app on my ipad at work with the dashboard displayed how often should it refresh? The attached screenshot GHL shows 6:47 AM...
  19. Replies
    19
    Views
    6,586

    Mitra 7206 will not start up

    Unplugged my lights and now one of them will not start up the other took about 10 minutes to boot up. The GHL logo flashes every 3 seconds.


    https://youtu.be/_9q_97Dx2BM
  20. Replies
    3
    Views
    2,026

    Now the myGHLdevice is gone also

    Now the myGHLdevice is gone also
  21. Replies
    3
    Views
    2,026

    Local Devices Gone

    I had 4 local devices set up on the app P4, P4 Hotspot, LX7 Left and LX7 Right and today they are no longer there. Do I have to go back and set them up again?
  22. Replies
    5
    Views
    6,750

    One more question. I have two of the 7206 lights...

    One more question. I have two of the 7206 lights and two of the flex mount 2 mounts. Is the best spacing to center each light over half of the tank or is there an offset that would be better?
    ...
  23. Replies
    5
    Views
    6,750

    Which way would you mount them? Like the way the...

    Which way would you mount them? Like the way the Flex Mount system 1 or 2 orientates them.
  24. Replies
    5
    Views
    6,750

    Lights for a 48" X 24" X 20" tank

    Would two LX7204s be enough for a mixed reef or should I go with two LX7206s?
Results 1 to 24 of 24